2950 HWY 48 SOUTH
FAX 615-446-9418 UNDERSTAND PRICES LISTED ARE SUBJECT TO CHANGE WITHOUT ANY NOTIFICATION HERE.
Check website for the latest on parts and prices. www.eccarburetors.com
EC DISTRIBUTING universal front axle assy fits many applications. Was designed for a direct fit for MTD and Murray wide body chassis. Will build to your specifications. Complete axle as you see it above 16" center beam works with 6x6 to 6x7.25 rims. Axle pictured above is with the very new billet spindles.
FCRP-4058 As pictured above less front hubs 245.00
FCRP-4058-1 As pictured above With front hubs 265.00
Rear 4 on 4 billet aluminum hubs complete with hardware.
FCRP-4074 3/4" axles 30.00ea.
FCRP-4075 1" axles 30.00ea.
FCRP-4076 1-1/4" axles 30.00ea
First picture is ground side Second picture is engine side will have a steel center hub with with a 1/4 5 hole blot pattern and two set screws. Designed to be able to remove the pulley yet leave hub in place.
The trans/transzxle pulley's will be all aluminum including hub and all one piece.
BILLET ALUMINUM BILLET PULLEYS
FCRP-4071 8" motor puley Price $59.95
FCRP-4072 6" motor Pulley Price $59.95
1" bore hub with mounting hardware for 8" and 6" pulleys Price $18.95
FCRP-4077 5" trans/tranny pulley Price $49.95
FCRP-5078 4" trans/tranny pulley Price $42.95
Pictured is a walbro on a 12 hp Briggs engine this is our Dominator series carbs. We have these ready on the shelf along with a tecumseh carb for the 8 HP and for the V-twins. specify which engine when calling. We will build a carb to your engine call for pricing.
Walbro Briggs Dominator 239.00ea.
Tecumseh Dominator 239.00ea.
Cutom built carbs call for Pricing
FCRP-4070K Billet Clutch assy. complete with
belt giudes and mounting hardware 129.00
This is the needle kit we sell in order for you to make your high side adjustable. $10.00
This is our tecumseh single or v-twin carb single comes with match airfilter adapter. These are massaged for optimum flow and jetting is changed. Want different jets to experiment with ask. They only fit the EC built carbs. 239.00 ea.
Fits carburetor in above picture 12.95
316VS Briggs Walbro filter adapter 12.95
641 K&N 10* Air Filter for the above adapters 14.95
Fits the Tecumseh V-twins. comes with mounting bolts 42.95
Fits the two barrel Vanguards and most other brands that use the
two barrel carbs 42.95
Fits Filter adapters FCRP 4056 and 4057 (both twin Filter adapters 42.95
This is our new hub and sprocket sets for the 700 or any tranny using the 32 or 9 spline shafts.
FCRP-4084 31 spline hub $19.95
FCRP-4085 9 spline hub $21.95
FCRP-4086 12 tooth sprocket $17.95
FCRP-4087 13 tooth sprocket $17.95
FCRP-4088 14 tooth sprocket $18.95
FCRP-4089 15 tooth sprocket $18.95
FCRP-4090 16 tooth Sprocket call for pricing Now available
FCRP-4091 17 tooth Sprocket Call for pricing NOW Available
Turf Pro rear tires 16x7.5x8 .
Turf Master front tires 13x6.5x6 25.00ea.
Turf Master 16x7.5x8 4ply rear tires in stock call for pricing, I don't remember....
True roll 6.5x6 Aluminum 3 bolt front rims .
True roll 7.25x6 Aluminum 3 bolt front rims .Here is the single OHV rockers, 175.00 a set and are ready for shipment. just in time for CHRISTmas orders.
.Here is the roller rockers mounted in an INTEK V-Tiwn. These are ready to go. 300.00 for a complete set.
The Vanguard are ready also look the same But I have no motor here at the time to show them installed. They too will be 300.00 for a complete set.
We have our own line of Sprockets from 42 to 50 in two teeth increments, #40 pitch split aluminum fits our new 1 1/4hub and all our goodies are now anodized red as you can see.
Pt# 501 Hub 27.50
PT# T5315-(# of Teeth) Sprocket starting at 26.00 and up.
Below is the new air filter system for the intek v-twins. You have the one billet turn up it replaces the plastic turn up on the front of the carb then it uses the vanguard adpater and filter. Total price for the whole kit 148.90. Some mods are required to the shroud area.
Here is out T-Shirts $7.00 ea. The Ec logo on front and a picture of the back logo...
Thanks to TIM RAGSDALE for being our Model.... That got him a free T
Front brakes designed to fit our front axles or any axle with a 5/8 stud simply machine a 3/16 keyway and tighten set screws. Brakes come as you see them in the picture. Brake line and master cylinder is seperate due to the many different applications and trying to save the race a dollar. Price for complete set is 420.00. That both sides. 60 cheaper than the Hegars.
Transaxle brake hat, machined for 1"axle but will also have a sleeve you use for a 3/4 inch axle. Don't have a price on it yet.
Below is the EC transmission As you can see it is a mower transmission. Price not set yet soon as we get them will let you know. I have been hammering on this one have 7 to 10 races so far, Jake has dropped the clutch till he got tired and quit and have yet to do any damage. But here is what they look like.
OK the transmissions are IN race ready add oil and go no reverse Standard 5 speed transmission Steel input and bevel gears thrid gear is 25/25 gear set. THESE ARE NOT PEERLESS. They ARE a direct replacement.
MORE TO COME AS TIME PERMITS