heymow.com - Lawn Mower Racing Forum
September 20, 2014, 04:57:37 AM *
Welcome, Guest. Please login or register.

Login with username, password and session length
News:
Want to Join our site? CLICK HERE
 
  Home Help Search Calendar Staff List Links Login Register  
  Show Topics
Pages: [1]
1  Engine Help / Kohler Engines / CH20 Twin Lifter's on: April 10, 2014, 08:14:28 PM
I have read here and a couple other places that Small block Chevy lifters will work in a Command Twin. If they will is there any thing special i need to do. What about the rocker arms will they also work? Also does any of you know the part number for the head studs, I want to swap out the head bolts and use studs instead.
2  Engine Help / Kohler Engines / Head question on: April 05, 2014, 10:18:07 AM
Is there any difference in the CH20 and CV20 heads? It's a CH20S Spec 64510 S/N 3319007311 The engine has a bad valve guide. Also will say a CH25 Head work on this motor?
3  Engine Help / Kohler Engines / Ch20 v twin Carb problem on: March 19, 2014, 09:55:26 PM
I'm working on a Kohler Family 3KHXS.6242GC, Model CH20S, Spec 64510, S/N 3319007311. I am looking for a Carburetor that will fit other then the factory emission friendly carb. The carb on it is gummed up bad and I cant get it to run right. It idles fine and the high speed is good it's off idle that is giving me fits, I have soaked it over night 3 times, sprayed it out with carb cleaner and blown it out with high pressure air from my compressor each time. I even replaced all the seals and gaskets and slow idle needle valve so it's rebuilt. This isn't my first rodeo but for the life of me I cant get this thing to work like it should I think it is a loosing battle. The guy I got the motor from let it set for a few winters with un-treated gas and you guys know what happens. I'm looking for a non emissions carburetor that will fit if there is a alternative. I do have two good carburetors off a 18 hp Briggs opposed twin if you guys know of an adapter that will work would be nice also.
4  Engine Help / Briggs Flathead / another rod question on: June 29, 2009, 11:39:37 PM
I didn't want to hijack another post. I was reading and I Quote dyoung14
"i dont know the sizes but the numbers, but i do know that a 40 ci has a longer rod than the 42, i have a 42 that i put 40 rods on my 42 crank and didnt mill the pistons, i put 40 ci heads on and have plenty of clearence, and it runs like a bat out of  well you get the point" Will this really work putting 40 rods on a 42 and not mill the pistons?  Would I use the 40 pistons or the 42?  Ive read that the pistons need to have .05 milled confused







     
 

 

 
5  Engine Help / Briggs Flathead / 18 hp opposed on: June 21, 2009, 11:51:42 PM
Is the crankshaft in a 18 hp opposed horizontal the same as the vertical. I have a chance to get a vertical shaft to use for parts for for my horizontal cheep just wondering if the cranks will interchange.
6  Engine Help / Briggs Flathead / opposed twin rod on: May 28, 2009, 08:29:26 AM
Hello, I have a B/S opposed twin, The engine is stock except I removed the govener and added a 2 into 1 Header. Im rebuildeing the engine and need a little advice on the rods. Im not a lawn mower racer, the engine is in a golf cart used for hunting and fishing. Im not trying to make it go fast I just needed torque (This engine has plenty)to pull a jon boat down the trail. I read a post here (opposed twin mods) it was suggested that the top rod needed to be fliped over. Mine is a horizontal shaft engine so Im assuming the top rod would be the flywheel side. Does the oil hole need to be turned facing up, facing the cam? You guys have a good thing going here I enjoy reading your post. Thank you for yor time.
Pages: [1]
Powered by MySQL Powered by PHP Powered by SMF 1.1.18 | SMF © 2013, Simple Machines Valid XHTML 1.0! Valid CSS!


Google visited last this page July 26, 2014, 06:25:05 PM