heymow.com - Lawn Mower Racing Forum
August 30, 2016, 03:47:58 PM *
Welcome, Guest. Please login or register.

Login with username, password and session length
Want to Join This Forum?  Click Here!
  Home Help Search Calendar Staff List Links Login Register  
  Show Topics
Pages: [1] 2 3 4
1  Mower Building / Setup Help / Garden Tractor Pulling / CUB on: April 17, 2013, 10:37:47 PM
This was the winter project. Well part of the winter!

Seems like I get them started but.....
Will see what happens.
Had a lot of welding practice on this one!
2  General / Coffee Shop / copper butt weld backer on: December 26, 2012, 06:21:40 PM
does any one know of a more inexpensive source?

3  General / Coffee Shop / weld through primer on: December 20, 2012, 07:48:59 PM
Is 3M weldthrough primer really worth the extra money?
4  General / Coffee Shop / sprint cars on: October 14, 2012, 05:46:27 PM
Excellent sprint car races last night! They had a couple of old school cars on display. Here is one of them.

5  General / Coffee Shop / cheaper? on: April 24, 2012, 08:29:54 PM
Does any one know perhaps where I can get these cheaper?

6  General / Coffee Shop / space station on: August 14, 2011, 09:44:22 PM
saw the space station a little earlier looked like a light bulb in the sky right where they said and right at the time they said pretty cool

7  Mower Building / Setup Help / Chassis / minimum deck requirements on: August 13, 2011, 06:50:54 PM
So I have this mower and the complete deck, and I have read the rules but i am unclear how wide that i should make the pieces that i am gonna cut for the deck. This will be a project in the future I just want to cut the pieces now so that I can recycle the rest of the deck. Along with the rest of my junk!!!!!

Thanks guys

8  Mower Building / Setup Help / Other Interesting Builds / building a hauler. on: June 12, 2011, 07:49:35 PM
I've been working on a hauler started out as a 4x8 open trailer improving my welding skills as I go along. Unfortunately my other project on here is on the back burner. Anyway I need somewhere to store my tractor when it is finished.

9  General / Coffee Shop / engine test stand on: March 05, 2011, 08:28:47 AM
I am building an engine test stand. I am ready to have the hole cut in the engine mounting plate. Six inch diameter will work with the single. Will it also work with a v-twin?

10  General / Coffee Shop / snap rings on: February 26, 2011, 06:46:59 PM
whats the proper cutter to use to cut snap ring slots  in a shaft

11  General / Coffee Shop / rebuilding hard drive on: February 14, 2011, 05:39:00 PM
do you install operating system or device drivers first
12  General / Coffee Shop / RAGB on: January 26, 2011, 05:44:10 PM
Does the verticle shaft in the peerless 1000 RAGB come out from the top of the gear box? I don't want to take it apart yet, but I would like to know. The exploded diagram seems to show that would be the case but I am not sure.


Tim Johnson
13  General / Coffee Shop / boring bar on: January 08, 2011, 11:30:20 PM
where is the best place to buy an adjustable boring bar for a mill? Need 1.100 inches. The ones that I have find are quite pricey, unfortunately thats probably going to be the case. Any setup tips from you machinists out there?


14  General / Coffee Shop / ignition timing on: December 23, 2010, 09:10:33 PM
Found this on the net sorry dont remember where

An engine at 6000 RPM has 100 Trigger pulses per second so the flywheel turns 360 degrees in 1/100th of a second so to change the timing one degree we will only have to delay the trigger pulse by 1/3600th of a second. Is this math right i think it should be 1/36000th of a second ie. (.027ms)/ degree of timing at 6000RPM.

Am I missing something?
15  Mower Building / Setup Help / Driveline / Peerless 2300 on: December 16, 2010, 08:00:01 PM
Brake shaft seal is leaking wasn't when first put back together anyway can the seal be changed successfully without tearing the transaxle apart?

Can get seals at

Pages: [1] 2 3 4
Powered by MySQL Powered by PHP Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Valid XHTML 1.0! Valid CSS!

Google visited last this page February 21, 2016, 11:34:36 AM