Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - jerb

Pages: 1 2 [3] 4 5 ... 147
31
Racing Mower Builds / Re: Geos W.O.O Modified Build
« on: June 20, 2012, 12:42:29 AM »
George, if memory serves me correct the peerless number is 788035a....ok i looked it up, not sure they are still available, i ordered a few, but been couple years ago, surely somebody can cross reference the number, i think it was a national seal, but not sure on that

32
Coffee Shop / Re: kohler vs another b& s
« on: June 19, 2012, 01:45:47 AM »
i have raced the briggs single for 5 years only had 1 failure and it was my fault ran 3 seasons on a set of valves the head on the intake one broke off and that all that i had with them.
my thoughts exactly.....have ran briggs singles for quite a few years and never lost one, make sure the clearances are spot on, use good parts and keep timing within reason and they are very reliable and build good power too!

33
Briggs OHV & Vanguard / Re: 40 intek 49 pistons
« on: June 19, 2012, 01:40:00 AM »
So it cost you $2k for pistons and a bore job?
ouch....and i thought the machine shop prices were high around here... :lol:

34
Tires / Re: 8x8 beadlocks
« on: June 18, 2012, 04:48:48 PM »
off topic but what ya building Nick?

35
Driveline / Re: drive pulley
« on: June 17, 2012, 03:30:14 AM »
i have used 1'' split locks on each side of pulley to help keep it in posistion

36
Racing Mower Builds / Re: ARMA super mod!
« on: June 13, 2012, 01:11:32 AM »
well i got it all to fit, lol...had to move the outer bearing over a bit,





i kinda dig the old school look of lawn mowers, i like the newer hoods and fenders, but i had this old stuff...lol

raised the fenders up about an inch as well, so as it sits have about 1 1/4'' clearance, built everything with mower tires in mind but my plans changed...lol
ride height about 2 1/4'' in the rear and a little less in front, planning on some new front rims and hoosiers for the front here pretty quick

37
Racing Mower Builds / Re: ARMA super mod!
« on: June 12, 2012, 12:53:47 AM »
well you spoiled my fun Larry...lol, i was hoping 1 1/2-2'' and even that is gonna require some surgery on my fender mounts, cant remember where i read that you should have wheels and tires before mounting anything.... :dunno: :dunno: :dunno:

38
Racing Mower Builds / Re: ARMA super mod!
« on: June 12, 2012, 12:31:24 AM »
ok...you guys that run the hoosier rear tires, what is a good safe measurement for clearance to fenders and chassis (3rd bearing framework)? running 16x8.50-8 tires on 8x9 rims....thanks

39
Racing Mower Builds / Re: Geos W.O.O Modified Build
« on: June 11, 2012, 12:44:04 AM »
George, get two of these stacked on top of each other to take the place of the bushing, works real good and will solve the problem for good, ran that setup for several seasons and never had a bit of problem, they also make a 1'' tall bearing you can use, but two of these is about perfect to replace the stock bushing, may have to add or remove a shim under the pinion gear....
http://www1.mscdirect.com/cgi/NNSRIT2?PMAKA=09017302&PMPXNO=1793388&cm_re=ItemDetail-_-ResultListing-_-SearchResults

40
Racing Mower Builds / Re: ARMA super mod!
« on: June 08, 2012, 08:40:56 AM »
well i received the wheels and tires 16x8.5-8 hoosiers mounted on 8x9 rims (thanks Drew), wow these things should put some power to the ground, hope to get them mounted on the chassis on tuesday, i will have to move the 3rd bearing in about an inch for plenty of tire clearance, but not too big a deal, i will get some pics posted soon!

41
Driveline / mcp caliper
« on: June 06, 2012, 11:21:38 PM »
anybody have the width on a cast mcp caliper?
i found the size...thanks

42
Racing Mower Builds / Re: ARMA super mod!
« on: June 06, 2012, 10:38:22 PM »
one of these days im gonna pour a new floor in the garage, but keep spending all my money on this thing...lol

43
Racing Mower Builds / Re: New MTD IMOW build
« on: June 06, 2012, 07:59:16 PM »
looks real nice.... :thumbsup: :thumbsup: :thumbsup:

44
Racing Mower Builds / Re: ARMA super mod!
« on: June 06, 2012, 07:53:32 PM »
well i got the running gear somewhat done, still need to notch the fender for the chain and build a tensioner for the chain, may have to move the outside bearing in for tire clearance, went with a little wider tire than i planned on so we shall see, but wont be a big deal to move,

45
Racing Mower Builds / Re: ARMA super mod!
« on: June 05, 2012, 12:38:28 AM »
i wish.... :lol:

Pages: 1 2 [3] 4 5 ... 147