Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - mowmaster

Pages: [1] 2 3 ... 10
1
Briggs Flathead / Re: tachometer
« on: June 01, 2007, 06:49:37 PM »
no, mine dosent,
However, yours might? :doh:
Andrew

2
Briggs Flathead / Re: Brass on cam
« on: May 31, 2007, 04:28:13 PM »
Yes, it is filler rod for acetelyne-gas welding.
You can get it at a welding supply, or tractor supply @ mytsc.com
Andrew

3
Tires / Re: Low profile tires...
« on: May 31, 2007, 04:25:26 PM »
I know, those are rediculous :lol:
Usually anyone you see with them, one usually dosent spin or clicks?
I dont get it :confused:
Andrew

4
Tires / Re: Low profile tires...
« on: May 31, 2007, 01:42:35 PM »
Try buggiesunlimited.com , they have every tire size, and from knobbies to slicks,
to even those lame spinners.
Andrew

5
Briggs OHV & Vanguard / Re: 18.5 BRIGGS wont start, Help!!!!
« on: May 30, 2007, 08:19:53 AM »
usualy if the polarity is backwards, the starter will whine, but not engage., Because it spins back wards, also if it dosent engage there is not enough juice.
Andrew

6
Briggs Flathead / Re: tips for most power in a stock rebuild
« on: May 29, 2007, 08:09:24 PM »
have a high-flowing exhaust, make a large air cleaner that will scoop air (so face towards the front). And personnaly, i would not completely remove the governer, i would adjust it untill it what you need.
Andrew

7
Briggs OHV & Vanguard / Re: 18.5 BRIGGS wont start, Help!!!!
« on: May 29, 2007, 08:06:45 PM »
Another thing to try is place your hand on the screen/cover of the flywheel
and try to turn it over, if it is dificult to do on any other stroke but the compression stroke
something could be wrong.
Andrew

8
Briggs Flathead / Re: pipes?
« on: May 29, 2007, 07:35:09 AM »
Ok guys, i pulled off the pipe, and what do i find.....
NO GASKET!!!!! I did not have time to start her up, but could this be the problem?
Andrew


Also, thanks for your help.

9
Driveline / Re: chain choices?
« on: May 29, 2007, 07:32:32 AM »
I agree with allen, also remember that your weakest link is your strongest.
Also keep in mind that unless you have one custom built(#35), Sprockets for a #40 &#41 chain
is more available, because that is what's used on dirtbikes, atv's, and some go karts.
Andrew

10
Briggs Flathead / pipes?
« on: May 28, 2007, 08:48:47 PM »
On my 12 HP Briggs i run 1" for about 8 inches, then it goes to 2 1/2"
the rest of the way(about 32"). However when at full throttle, if i quickley
let off down to an iddle, it makes a few loud pops.  :doh:
Is this because of back pressure, if so can i cut the pipe about 15" back and weld
a 2.5" washer with a 1 1/4 " hole in it, the weld the other half back on?
Also, this it the first time i have ever had this problem, 1-because i never use pipe this large, i only use 1-1.5" on my other racers.
2- Because all my pipes come out in front of the rear wheel, this one comes out behind the front left wheel.
This exhaust was an experiment,  and sounds good idelling.
Andrew

11
Briggs OHV & Vanguard / Re: Fire slot
« on: May 28, 2007, 08:38:59 PM »
This is only applicable to flathead engines, and it directs a path for the flame to travel over.

12
Briggs Flathead / Re: tips for most power in a stock rebuild
« on: May 28, 2007, 08:32:53 PM »
I am assuming that a good Port & Polish is out of the picture?
Is that all the rules, or give us the specifics.
Andrew

13
Briggs Flathead / Re: boring help?
« on: May 28, 2007, 08:30:10 PM »
Arc Racing provides this service. When you bore away from the valves you get increased throttle response and a higher top end. However, there is a longer flame travel, however if you bore closer towards the valves you get a better low end. Go to , or call ARCRacing.com
they can better explain this. :twothumbsup:
I'll be happy to answer anymore questions.
Andrew

14
Briggs Flathead / Re: boring help?
« on: May 27, 2007, 05:45:09 PM »
As long as it is strait, go for it.
Also go 0.001 over for the rings and several honings.
Andrew

15
Post your Pics! / Re: Murdr Mowchine 2
« on: May 27, 2007, 09:39:01 AM »
looks great, by the way what size drive pulley are you going to run?
Andrew

Pages: [1] 2 3 ... 10
anything