Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - oldmanracer

Pages: [1] 2
1
Mower Engines & Parts / Wtb arc billet vanguard long rod
« on: August 19, 2019, 09:34:05 AM »
Looking for a vanguard arc billet long rod if anyone has one laying around thanks

2
Briggs OHV & Vanguard / Vanguard timing
« on: May 15, 2019, 12:56:03 PM »
Does anyone know what stock timing is on a 23hp vanguard, and when setting the timing using arc adjustable flywheel the timing marks are supposed to to line up using a timing light on the btc side correct?

3
Briggs OHV & Vanguard / Safe rpm's
« on: February 28, 2019, 01:01:15 PM »
Looking for recommendations for safe rpm limits for my build 38ci vanguard, billet rods, billet cam, billet flywheel,billet push rods,je pistons, shaved heads ported and o-rined thin copper head gasket,double valve springs with shims,big bore 2barrell carb,thanks for opinions

4
Briggs OHV & Vanguard / Head gasket
« on: January 06, 2019, 05:59:48 PM »
I have a 21hp vanguard with flat top pistons that sit in the hole .050" right now it has the .032" copper head gasket could I run a thinner copper gasket?

5
Briggs OHV & Vanguard / Push rod length
« on: December 31, 2018, 06:01:28 PM »
Looking for some advice on how to measure and install the cut to fit chrome moly push rods on a vanguard engine, thanks

6
Briggs OHV & Vanguard / Outboard mounted clutch
« on: February 21, 2018, 12:09:17 PM »
I have a noram enforcer clutch that mounts outboard and 3 times now the mounting bolt keeps breaking, tried higher grade bolts already, any ideas what could be wrong or what I should look for, thanks

7
Briggs OHV & Vanguard / 21/23 vanguard piston
« on: November 22, 2016, 03:40:33 PM »
What is the biggest flat top piston you can put in there without resleeve

8
Briggs OHV & Vanguard / 23hp vanguard opinions
« on: August 07, 2016, 02:33:49 PM »
Currently running a 23hp vanguard with the 16hp crank long rods with flat top pistons and all the other performances parts,question is would going back to 23 crank with stock length rods give me more power or what your opinion on this setup,thanks

9
Briggs OHV & Vanguard / Vanguard cam
« on: June 04, 2016, 12:53:38 PM »
Just looking for opinions on the best cam for a 23hp vanguard, I've ran the cheetah cam and there a good cam, anything better out there?

10
Briggs OHV & Vanguard / 38ci 2 bbl intake
« on: February 12, 2016, 11:05:04 AM »
Does anyone sell a ported/polished 38ci 2bbl horizontal intake

11
Briggs OHV & Vanguard / Roller rockers
« on: February 08, 2016, 09:28:13 AM »
Is there any hp gains at all running roller rockers or is it for reliability

12
Briggs OHV & Vanguard / Billet tappets
« on: February 01, 2016, 03:04:32 PM »
Anyone run billet tappets with no problems and are they even worth the cost

13
Briggs OHV & Vanguard / 23hp vanguard pistons
« on: November 01, 2015, 04:22:41 PM »
Does anyone know what the maximum you can bore these engines is and what aftermarket pistons are there to fit, i'm looking for maximum bore and piston combo, thanks

14
Briggs OHV & Vanguard / Fuel Usage
« on: May 11, 2015, 08:27:22 PM »
hi guys, i have a 20hp vanguard twin built up somewhat and my question is last season with stock heads during a regular race i would use almost a whole tank of fuel, same motor this season runs strong but during off season i had my heads ported and polished larger stainless steel valves done by well known guy that knows what he's doing on these heads, but expecting to use more fuel i'm using alot less, any concern here?

15
Briggs OHV & Vanguard / Re: is this set up wrong??
« on: February 20, 2015, 12:56:30 PM »
Would there be any advantage to having a spacer between the intake to elbow and elbow to carb or better with just the one spacer

Pages: [1] 2