Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - wegian_63

Pages: [1] 2
1
Chassis / Re: JD STX38 - Steering question - Light front end
« on: July 30, 2013, 11:58:45 AM »
I havent had a chance to go pick up some scales yet

I run for tires 16x7.5x8 rears, 13x6x6 fronts
700 tranny
6in front
4in tranny
12 tooth front sprocket
47 tooth rear sprocket

Front axle has 12 degree camber

2
Chassis / Re: JD STX38 - Steering question - Light front end
« on: July 23, 2013, 11:56:36 AM »
I will have to gather that info tonight, as I havent checked since my last race at end of June.


3
Chassis / JD STX38 - Steering question - Light front end
« on: July 23, 2013, 10:16:13 AM »
hoping someone can help me with an issue I am having

I run a JDSTX38 and right now I am having major troubles with cornering.  I have tried different angles, TOE out setups and i push thru the corners.  I have a sharp entering the corner but then once I grab the throttle it pushes out until i hit the rough edges and then grabs strong.

I am going to try some different wheels up front but just feels like I am pushing thru the corners.

Side note i will pull wheelies out of the corners too.

Can I add weight up front to help this?

4
Chassis / Re: John Deere STX 30 Build or not to build?
« on: July 23, 2013, 10:12:46 AM »
oldiron, I live in Glyndon, MN and I run a John Deere STX38.

We race at family owned tracks, have about 10 mowers that regularly show up to our events.

I can send you some pics and information if you need

5
Chassis / Re: Hand Throttle
« on: May 07, 2013, 03:09:53 PM »
Thx guys I will have to check them out tonight.  George is that on the ECC website yet??

6
Chassis / Hand Throttle
« on: May 06, 2013, 09:06:50 AM »
I used to get my throttles thru Acme Mowersports, but the site is no longer.

Can someone direct me to another place I can order them thru, starting 2 new builds and trying to get all parts ordered?

Thanks!

7
Driveline / Re: sprocket question
« on: August 17, 2012, 03:23:23 PM »
will a 16x7.5x8 run on a 8x8 tire? it may be a dumb question, but those are the only ones I am finding.  otherwise need some new rear rims also.

8
Driveline / Re: sprocket question
« on: August 15, 2012, 12:32:39 PM »
thx, I dont have any 16's at home, so it looks like I get to go shopping again!! haha

Burwell555, are you running a kohler on your JD?

9
Driveline / Re: sprocket question
« on: August 14, 2012, 11:33:19 AM »
i could maybe put a 7 in pulley on, but it would be close.

I will check out the speed calc, i actually think I have a set of 16's on my spare transaxle.  I will have to check it out tonight.

10
Driveline / Re: sprocket question
« on: August 14, 2012, 08:42:37 AM »
what size would you recommend?

11
Driveline / Re: sprocket question
« on: August 14, 2012, 08:36:45 AM »
yeah 18 wheels, I will be changing them soon.

12
Driveline / Re: sprocket question
« on: August 14, 2012, 07:59:23 AM »
stock motor, govenor removed, running aroun 4950 rpms at full throttle.  100 foot straight aways.

13
Driveline / sprocket question
« on: August 14, 2012, 07:38:42 AM »
I ran in a race last weekend and i just dont think I have the right setup yet.  I have a JD STX38, 12.5hp, running 6 in on Engine, 4 in on 700, 12 sprocket on trans and 46 on axle, I had pretty good distance speed, but lacking acceleration.  Thinking of jumping to a 14 sprocket on trans? 

any help would be appreciated, thx

14
Chassis / Re: Steering problems
« on: August 07, 2012, 07:01:31 AM »
Thanks for the responses!! I will take your notes and make the changes tonight and report back!!

15
Chassis / Steering problems
« on: August 06, 2012, 03:08:49 PM »
i followed the acmemotorsports Direct Steering and now having some problems.

for one it is pretty tough steering.  I have a John Deere STX38. I attached pics any help would be appreciated.

Turns really well to the Right, actually over turns, and doesnt want to turn to the left much at all.  Plus it is just tough steering.

Pages: [1] 2
anything