Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - ARC C63

Pages: [1] 2 3 ... 10
1
Briggs OHV & Vanguard / Bandolero's versus stock vanguard
« on: June 16, 2017, 06:23:05 PM »
I need some help I bought a Bandelero vanguard engine it's a 35 horizontal shaft when I pulled the heads off it's got flattop pistons not like the regular stock vanguards with the dish Pistons are these have different rod Lengths  than the stock do these require the stock of arc rods or do they require the longer arc rods like if you cut the dish off the Pistons

2
Want To Buy / Who Has It? / vanny parts
« on: November 26, 2016, 07:18:55 PM »
im looking for some stuff
 1 vanguard oil filter housing
 2 90* carb adapter
 3 vanguard Billet Flywheel or the hub for the center
 4 vanguard cam
 5 vanguard long rods

3
Briggs OHV & Vanguard / Re: 49ic winter build
« on: October 21, 2015, 06:16:21 PM »
I'm looking to spend about 1000-1500

On cam, piston, rods and maybe new carbs

4
Briggs OHV & Vanguard / 49ic winter build
« on: October 20, 2015, 06:26:11 PM »
building up my engine its a stock at this point with .030 under heads with ec springs and retender

im looking for help with is the best parts form the best places to build a good 60plus hp engine with out braking the bank
 how big can I bore the cyls
is their a stoker kit for the crank
can I get longer rods with flat top pistons
what is the best cam the will not snap
and anything else any help would be better

5
Briggs OHV & Vanguard / Re: Intake Manifold
« on: June 10, 2015, 10:19:16 AM »
can some one tell me if 806376 is round at the head or "D" shaped???

6
Briggs OHV & Vanguard / Re: vanny help!!!!!!!!!!
« on: June 10, 2015, 10:03:14 AM »
sorry that I didn't repost but I found a crack in the left hand exhaust valve. I only found it after the engine was hot and put my bore scope in

7
Briggs OHV & Vanguard / Re: vanny help!!!!!!!!!!
« on: September 29, 2014, 08:52:54 PM »
Im going to bring home my leak down tester and compression tester tomorrow ill also try to open up the lash

8
Briggs OHV & Vanguard / vanny help!!!!!!!!!!
« on: September 29, 2014, 08:17:44 PM »
ok I have a 35cu vanny with
arc flywheel set at 2 1/2 marks off -
ec big bore that I have cleaned
ec cam
arc rods .100 over
.100 cut pistons
Dual valve springs
valve lash is .003 all four
new e3 plugs .023 gap
new coils at .040 gap
new diod wire
new fuel pump
new fuel filter

mower runs like crap pops and misfires will nice at times then will loss all power stalls out when racing then starts right back up

can any one help me?  im throwing money at it at this poiont :bash: :bash:

9
Briggs OHV & Vanguard / Re: Fuel mix help
« on: August 05, 2013, 03:48:43 PM »
Idk what it was but I cleaned the card reset coil gap put 2 new e3 plugs in it gaped them reset lash and runs way better

10
Briggs OHV & Vanguard / Fuel mix help
« on: August 01, 2013, 01:38:45 PM »
On my vanny with a ec carb my right size is lean and my left side is ok maybe a little rich but not bad mostly up in the rpm it has a skip like around 7000 Amy one come a crossed this be four

11
Briggs OHV & Vanguard / Re: Inteck twin arc flywheel
« on: July 08, 2013, 07:13:32 PM »
Ok thank you tank

12
Briggs OHV & Vanguard / Inteck twin arc flywheel
« on: July 08, 2013, 05:09:39 PM »
My coils don't fit with the new flywheel and brackets the ground wire is hitting the brig

13
This is great to see that us in New England can all get together on one track.

14
Chassis / Re: Weight help
« on: June 23, 2013, 06:39:45 PM »
Good until the belt become apart big power handle great a little tlc and I will be good for mass next month

15
Briggs OHV & Vanguard / Re: Vanny running rough
« on: June 23, 2013, 10:33:14 AM »
You need exhaust and the mower Hot to get a good read and flicking the throttle is not good ez up the rmps

Ps it looks like rich seeing the flames coming out

Pages: [1] 2 3 ... 10
anything