Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - coreyk

Pages: [1] 2 3 ... 24
1
Briggs Flathead / Re: Quick governor question
« on: March 20, 2008, 02:13:00 pm »
I cleaned it again today and i guess i did miss a spot last time. Seems to be fine now. Idle's a little high and cant adjust it any lower on the carb, no biggy tho.

2
Briggs Flathead / Re: Quick governor question
« on: March 18, 2008, 06:57:29 pm »
Cleaned the carb today and it didn't solve the problem.

3
Briggs Flathead / Re: Quick governor question
« on: March 18, 2008, 01:24:36 am »
Thanks guy's appreciate it! ;)

4
Briggs Flathead / Quick governor question
« on: March 17, 2008, 03:07:06 pm »
I have a 13hp flathead briggs and it raises the idle then drops. i am pretty sure its not from the carb because the governor arm that comes out of the motor and is connected to the governor spring  moves back and forth when the throttle is all the way down. What can cause this?

5
Briggs Flathead / Re: 14hp carb on a 12.5?
« on: August 28, 2007, 09:55:31 pm »
thanks for clearing that up, wasn't sure. Is there anything i can do to the carb to get more fuel flow?

6
Briggs Flathead / Re: 14hp carb on a 12.5?
« on: August 28, 2007, 09:15:40 pm »
If i get a 31cu motor will the carb off that work, or will it flood it out?

7
Briggs Flathead / Re: 14hp carb on a 12.5?
« on: August 28, 2007, 08:49:01 pm »
The main jet is not any bigger in it?

8
Briggs Flathead / 14hp carb on a 12.5?
« on: August 28, 2007, 08:25:19 pm »
I have a 14hp carb off of a 14hp OHV briggs, i am thinking of putting it on my 12.5 briggs for more fuel delivery.... question is will it flood the motor out?

9
Briggs Flathead / Re: Isky cams
« on: August 28, 2007, 08:22:27 pm »
Where can you get one of these andhow much do they run you?

10
I was not sure if you should shave it anymore then it is. Also where can i buy an oversized piston and rings for the motor?

11
How much do you recomend i take off? It's an 11hp head on a 12.5 briggs that has a port and polish. Thanks!

12
Driveline / Re: confused again.
« on: April 03, 2007, 06:54:58 pm »
I feel like a dumbass. I sheared the keyway on the motor pulley.

13
Driveline / confused again.
« on: April 03, 2007, 05:18:55 pm »
Got my 600 back together and installed. Went for a ride did fine. Put my new exhaust on and went out for a ride. I was in third and downshifted into 2mnd. It would not move. I went through every gear and it just goes in gear and stays there. What can cause this?

14
Driveline / Re: confused.
« on: April 01, 2007, 10:18:52 am »
Did you have it apart and if so did you make sure you have the spacers in-between the gears correct, because if you inadvertently switched them you will never find second gear.

Yes i did. Maybe that is the reason.

15
Driveline / Re: confused.
« on: March 31, 2007, 09:05:28 pm »
Nope, i have splined gears in mine.

Pages: [1] 2 3 ... 24
anything