Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - GTX21

Pages: [1] 2 3 ... 35
1
Briggs OHV & Vanguard / Re: Vanny vtwin 14hp stock cam spacer
« on: February 17, 2013, 11:24:03 AM »
When you say measure is it from where the washer sat to the top of cam?(lobe side) or the side the ball and spring came out of?

2
Briggs OHV & Vanguard / Vanny vtwin 14hp stock cam spacer
« on: February 17, 2013, 10:40:23 AM »
I've searched on hear and read about a spacer that needs to be made in order to maintain oil pressure on a bare no governor stock vanguard twin cam. I've removed everything on the cam, it's now hollow. I just don't understand what the spacer is suppose to look like and the best way to do it. A picture of this spacer would help a bunch!

3
Driveline / Peerless 350 output hub and sprockets
« on: December 01, 2012, 10:50:43 AM »
Where can i get the correct splined hub that is able to have the spockets welded on to it for a perrless 350?

4
Briggs Flathead / Re: Opposed twin carb questions
« on: May 20, 2011, 12:43:53 PM »
Their is a couple different stock intakes. Theirs a two piece (aluminum I think??) intake thats alittle hard to find but easy to port, theirs a big cast one and a smaller cast one if I remember correctly. Rooster will chime in here soon and say whats what.

5
Open walk behind?? :confused:  Sounds tiring

6
Briggs Flathead / Re: Opposed twin carb questions
« on: May 18, 2011, 07:10:46 AM »
Just PM RunningOnEmpty, Im sure hed tell you everything you need to know, very nice guy!

7
Tires / Re: good or bad idea
« on: May 11, 2011, 07:26:34 AM »
Just make sure to actually measure the tire circumference and find out the difference, dont wanna be to much of a difference, but not to little. You will have to experiment with tire pressures, and possibly a few different set of tires, as they wont all have exactly the same circumference.

8
Briggs Flathead / Re: spittn', sputtern' & popn'
« on: May 10, 2011, 06:31:41 AM »
Opposed are know for that^

9
Tires / Re: good or bad idea
« on: May 10, 2011, 06:29:03 AM »
If rules allow it, id go for it, it should help with corner entery

10
Coffee Shop / Re: BAD WEATHER DOWN SOUTH!!
« on: April 28, 2011, 07:24:58 AM »
Looks like york county is in the clear for now, dont know if any touched down but i bet theirs wind damage, and flooding. Was really coming down in york earlier

11
Coffee Shop / Re: Backwards Vanguard
« on: April 28, 2011, 06:33:30 AM »
^^ Now that sounds like a very poor design, but I guess plastic is cheaper...

12
Briggs Flathead / Re: Opposed Twin Oil Mods
« on: April 26, 2011, 07:34:42 AM »
No, these can be done without balancing the crank (oil mods)

13
Have you tryed stock exhuast springs? :confused:

14
Non-Affiliated Races / Re: Season Opener at Selinsgrove 4/29
« on: April 25, 2011, 01:03:47 PM »
Great race track, I had many chances to look at it up and personal when their running the big half mile with sprints, nice smooth fast CLAY track.

15
Chassis / Re: Steering geometry quandry.
« on: April 20, 2011, 08:08:50 AM »
Toe in will help with going straight, (coming out of corner straightens up faster) Toe Out will help with entering a corner as the wheels are pointed slightly in that direction.

Pages: [1] 2 3 ... 35
anything