Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Rooster

Pages: [1] 2 3 ... 442
1
Coffee Shop / Re: USLMRA membership
« on: September 05, 2014, 01:30:45 PM »
Will paper Memberships filled out at the local Clubs be valid?

2
Briggs Flathead / Re: Oppy Carb Issue
« on: September 05, 2014, 01:27:28 PM »
I guess you could just push through the old pump?
You would need to cap pulse port, just in case membrane tears.

3
Coffee Shop / Re: 700 tranny shift keys
« on: September 04, 2014, 04:28:00 AM »
Because your running a 700...lol

Check the slots in the shaft, make sure they are not all goobered up.

4
Chassis / Re: converting from 6 inch wheels to 8 inch wheels
« on: September 04, 2014, 04:24:27 AM »
while you are modifying the fenders, remember you are now allowed to sink the seat into it to get the 13" seat height from the ground to the bottom of the seat.  If you are going by the uslmra rules ofcourse

Actually...you are.

5
Briggs Flathead / Re: Opposed Briggs 18hp
« on: September 04, 2014, 04:21:00 AM »
If you do run it on stock rods, clearance them and flip the top one!

6
Briggs Flathead / Re: Oppy Carb Issue
« on: September 04, 2014, 04:18:42 AM »
You will also have to drill the carb for a fuel line fitting.

7
Driveline / Re: To the peerless 400 lovers out there
« on: August 22, 2014, 12:39:27 PM »
Quote
Owen,

   How do you plan to "drill" the lightening holes in these gears?  These gears come in two types -- heat-treated steel or powdered metal -- and both types are hard.  Do you have access to special bits that will penetrate these metals, or maybe a laser cutter?  You'll need to be careful not to affect the heat-treating of the gears, especially the teeth and the bores.

http://youtu.be/c6wRLJWfjFw?t=47s

8
Newcomers / Re: uslmra rookie in illinois
« on: August 21, 2014, 03:51:11 PM »
I'm not trying to trade this mower in, it was my great grandpa's first mower and I finally got it running after 30 years of just sitting around. So it's got some sentimental value. What part of Michigan are y'all from? I live in Rockford... That probably wasn't wise of me, now roosters assassins know where to look!

45 years....LOL
I'm guess that's a 1969 Sears?
And if its got Sentimental value...add that to the reasons not to cut it up.....
I already knew where ya were, i have connections...little known fact that when Roosters crow, they are actually passing classified information about the locations of Antique Garden Tractor Molesters... which is why Garden Tractor Pullers don't eat eggs!!

Another tip....
It's Called
ALLEY CRUISING

Somewhere, under a upside down kiddie pool, with grass grown up ...is the perfect racing mower waiting for you ;)

9
Driveline / Re: To the peerless 400 lovers out there
« on: August 20, 2014, 07:53:58 AM »
If I was going to drill them, I'd chamfer the holes both for oil drag and stress relief.

Love the 400's!
The 350's I always blew them up!


10
Tires / Re: tire/rims
« on: August 20, 2014, 07:48:23 AM »
I think "clenching" means seating the bead???

11
Briggs Flathead / Re: 18 hp replacement coil
« on: August 16, 2014, 07:10:54 AM »
Hmm...Are these the "new Style" coils?

12
Newcomers / Re: uslmra rookie in illinois
« on: August 16, 2014, 07:09:03 AM »
HECK if you were close enough I'd give you a chassis to keep you from ruining that one!!

Ohh, BTW...that's not even legal to build for a USLMRA G/ P.

13
Newcomers / Re: uslmra rookie in illinois
« on: August 16, 2014, 07:07:32 AM »
The biggest thing that TRACTOR has going against it for racing is the transaxle is very low geared and has a lot of rotating mass. You say you've read on here....have you seen anyone building out if A TRACTOR????
No, we use MOWERS !!!


Now I understand building what you have. But son what you have is not a viable racing mowchine.

Your mechanics are right, you can make that thing fast. But you'll never make it handle, you'll never make it quick, you'll never make it turn.

The worst part is, you can easily find a better chassis!!

14
Tires / Re: tire/rims
« on: August 15, 2014, 01:20:31 PM »
I used a cheetah bead seating tool and it worked on all of my other tire applications thank you for the input

That's the best way!!

15
Briggs Flathead / Re: 18 hp replacement coil
« on: August 15, 2014, 01:17:31 PM »
do not buy the new coils they have rev limiter built in no good  :bash:

Really?? hows that work??

Pages: [1] 2 3 ... 442
anything