Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Topics - jerb

Pages: [1] 2 3 ... 7
1
Newcomers / thinking about coming back to mower racing
« on: September 09, 2015, 07:33:51 PM »
Well guys been playing with the idea of building another mod-x or super sportsman. What tracks close to kansas?? Been out of the loop for awhile now!

2
Briggs OHV & Vanguard / bolt pattern?
« on: June 09, 2013, 10:38:33 PM »
was wondering if the engine mounts the same bolt pattern on an intek the same as a ohv 28, what about the 31'' tecumseh single?
i cant find the ohv pan i had laying around!

3
Briggs OHV & Vanguard / mikuni carbs
« on: June 21, 2012, 02:50:15 AM »
anybody know of a chart to show what size mikuni carbs to use on various cc's or cubic inches? thanks

4
Driveline / mcp caliper
« on: June 06, 2012, 11:21:38 PM »
anybody have the width on a cast mcp caliper?
i found the size...thanks

5
Driveline / 10'' rotor
« on: June 02, 2012, 11:17:20 PM »
maybe George will chime in but does anybody know if the 10'' disc that EC sells bolts to a standard sprocket hub, i assume it does but didnt say bolt pattern on item description, thanks

6
Chassis / custom cables
« on: October 21, 2010, 10:04:50 PM »
anybody know a good place to order custom made cables? ie...throttle,clutch!

7
Racing Mower Builds / ARMA super mod!
« on: September 19, 2010, 08:39:26 PM »
well after trying to figure how to change a few things  on the super mod i was building i decided to start from scratch and learning from the mistakes i made on the first one, i believe this build is going to be way better and way stronger then old chassis, i started with a walk through mtd chassis, i uses 1 1/2'' square tubing for front axle and 1'' square tubing for chassis braces..




8
Tires / super mod front tires!
« on: January 31, 2010, 09:40:45 PM »
just curious what some of you guys are running for front tires in the super mod twin and single classes....thanks!

9
Driveline / sprocket diameter
« on: January 25, 2010, 11:12:49 PM »
anybody remember how to figure sprocket diameter, theres a figure floating around that takes tooth count x something to figure diameter, but can't find it and don't remember..... :lol:

10
Briggs OHV & Vanguard / intek v-twin
« on: January 16, 2010, 11:59:48 PM »
had a question for any briggs dealers, looking to order valves for a 44 intek, the numbers i came up with are 697576 ex. valve and 792200 in. valve, my question is do these come with the 2-piece locks, or our these the regular valves with the cheap slip on retainers, plan on using the 263 ec retainers....

11
Chassis / front axle question
« on: November 21, 2009, 09:16:59 PM »
hey guys, was wondering, on the endplates that weld to your axle tube, can the outside plate(the one that sets the caster angle be made out of aluminum? i was thinking ec front axle was like this, but not sure, thanks!   Tim

12
Chassis / ec front brake question
« on: November 13, 2009, 09:12:29 PM »
can anybody on here give me the length of their spindles if using the ec front brakes and where the keyway is cut in the spindle, thanks!

13
Racing Mower Builds / ARMA Super Modified Twin for 2010
« on: November 13, 2009, 06:17:50 PM »
well after finally going out to the bone pile and dragging a step through chassis out of the weeds, i now have a chassis to start working on, this will be a pretty slow build as time and money allows, although i hope to have it finished sometime around april or may, it will be powered by a horizontal van-guard twin, with a jackshaft and either a foot clutch or a cent clutch, havent decided on that yet, will have 6x7.25 rims up front and 8x8 rims on the rear and mower tires for now, this is what it looks like now...hope to get it tore down sunday afternoon and start  building the front axle and reinforcing the under side of the chassis...all for now, any ideas as i go along will be greatly appreciated...

14
Post Your Video / mowfast racing!
« on: September 27, 2009, 11:38:10 PM »
here is a link to a video of our mowfast races in smith center, ks, this is our sportsman class, bear in mind we all run stock un-governed engines, thanks rooster and the gang for making the long drive up for this race, the track was sweet and pretty good turnout to boot!!

15
Driveline / peerless 500 shift keys!
« on: August 31, 2009, 12:44:33 AM »
anybody have a part number for the 500 peerless shift keys, the local dealer cannot find a part number for these shift keys, thanks!!

Pages: [1] 2 3 ... 7
anything