Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - birdman_express

Pages: [1] 2 3 ... 200
1
Briggs Flathead / Re: Briggs New Rod
« on: July 03, 2018, 06:33:58 AM »
Hello,

Flathead 125k02 0303 e1 031117 fb

Any chance there is an aftermarket rod for this motor?

Thanks
Steve

Yrs.

2
Driveline / Re: RAGB gearing questions
« on: June 28, 2018, 07:49:55 AM »
I have the governor removed from my engine, what ratio should I be around ?

With the governor removed you should have a Billet Flywheel.

3
Briggs OHV & Vanguard / Re: Briggs and stratton 22hp vtwin quickening
« on: June 28, 2018, 07:30:36 AM »
What club are you going to run with?

4
Non-Affiliated Races / Re: PA MiniPro and Vigilante Karts
« on: June 24, 2018, 10:43:38 AM »
He is a spammer Tom.

5
Kohler Engines / Re: Kohler command single vs honda gxv???
« on: May 20, 2018, 07:03:27 PM »
As far as I know Honda motor is not legal in CP


Honda did have a vertical motor in a lawn mower, I worked on the only one I ever saw,
it came in the mower shop I worked at one time. I wanted to buy it from the customer.. LOL

6
Newcomers / Re: In over my head. Please read!
« on: May 13, 2018, 10:42:22 PM »
If you have Facebook, look up Carrier Performance, he is your Canada dealer for race mower parts. His new built mower just won on the first race out.

8
Chassis / Re: Stock mtd front axle
« on: April 22, 2018, 09:03:45 PM »
We all try to save some time and money where we can. Steering and brakes are not
the two places to do that. So get you some good 1 x 2 thick wall for the front beam
and get you the well your own parts from EC to finish it off, and have some good
steering geometry to boot.

9
Briggs Flathead / Re: Briggs opposed twin pressure lube
« on: April 22, 2018, 08:37:31 PM »
Thanks - I figured they were different.  I havent taken it apart yet, but I assume yes it has a screen/pickup in the sump.   I guess I will plan on getting it welded.  I assume that the material is cast aluminum?

There are 3 different styles of pans that all bolt on, you have to take it off and look.

10
Chassis / Re: Stock mtd front axle
« on: April 22, 2018, 08:15:08 PM »
Worst crossbar as you call it in the mowers.
Out of the 40 mowers I have torn down, only
about 3 were not damaged to reuse on a grasscutter.
I sent you a message.

11
Chassis / Re: Stock mtd front axle
« on: April 22, 2018, 07:41:09 PM »
Stock mtd front ends are for mowing. So nothing is what I would advise.

12
Briggs OHV & Vanguard / Re: Outboard mounted clutch
« on: February 22, 2018, 07:04:17 PM »
If the clutch has loose tolerance on the shaft, it can break or back out the bolt.

13
Honda and Clone Engines / Re: offroad mower
« on: February 11, 2018, 10:00:40 PM »
We do not do offroad mowers, a predator 212 is not a common motor used in mower racing.
Things are slow right now, and the mass of members are not around to answer questions.
Do a search on 212 and see what you come up with. Maybe you could send a message to one
of the members who use them in one of the few clubs that may use that motor.
Go-karts use this motor as well as some mini bikes guys. You may want to try one of those sites
to help dial in your setup.

14
Racing Mower Builds / Re: Snapper racing mower build
« on: February 08, 2018, 10:34:05 PM »
Question: where is a good place to buy parts?
I looked at bmikarts for parts of the axle and 2 wheels but shipping alone will send me back 150 dollars.
A good shop somewhere in the e.u. would probably save me some extra money

The E.U. all buy from the US what they can't make. Shipping will always be the highest cost.

15
Racing Mower Builds / Re: Snapper racing mower build
« on: February 08, 2018, 04:03:13 PM »
Nice... what club do you race with in Israel?

Pages: [1] 2 3 ... 200
anything