Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - MIKE/PRECISIONCAMS

Pages: [1] 2
1
Honda and Clone Engines / Re: Big Block Clone & Dyno Results
« on: February 10, 2016, 10:40:12 PM »
Its around a 28 cubic inch motor , as far as a billet head, I have seen them for this engine before, I think they only made a few.  They cost more than this complete engine.  This is not anything all that special in our shop, its one of our kits we build all the time.  This is a kit that gets a lot of horsepower for the Money, and our customers have been happy with results.

2
Honda and Clone Engines / Big Block Clone & Dyno Results
« on: February 09, 2016, 12:14:14 AM »
When the Clone is bad to the bone!

Precision Cams
910-251-0612
precisioncamspower@gmail.com

3
Briggs OHV & Vanguard / Re: Billet tappets
« on: February 01, 2016, 09:35:05 PM »
They work well in flatheads because we have to reduce the base circle of the cam so much not to run into everything.  The extra length of the billet tappets makes it easier for the builder not to have to weld on the valve stems.   As far as OHV engines, that is a different conversation.  You want to make sure the face of the tappet is the stock size or at least the size that the cam was designed for, if it is different than stock. 


Mike Edwards

4
Briggs OHV & Vanguard / Re: Intek vtwin cams
« on: January 20, 2016, 10:20:55 PM »
We have a new .370 cam with real good results on testing. Call me anytime.

Precision Cams
Mike Edwards
910-251-0612
precisioncamspower@gmail.com


5
Mower Engines & Parts / Re: PRECISION CAMS
« on: January 17, 2016, 11:46:57 PM »
Bringing you mow power for 2016! New Intek and Vanguard profiles available - in cast or billet cores.

Precision Cams
Mike Edwards
910-251-0612
precisioncamspower@gmail.com

6
Briggs OHV & Vanguard / Re: Intek vtwin cams
« on: January 17, 2016, 11:20:14 PM »
We have a new profile for 2016 that's really picked up the power. Let us know if we can help.

Precision Cams
Mike Edwards
910-251-0612
precisioncamspower@gmail.com

7
Briggs OHV & Vanguard / Precision Cams - new Intek Twin profile for 2016!
« on: January 17, 2016, 11:03:25 PM »
Precision Cams introduces a new Intek Twin profile to pick up your speed in the new year. Works for the 40, 44, or 49 engines.

Any questions contact:
Mike Edwards
910-251-0612
precisioncamspower@gmail.com

8
Briggs OHV & Vanguard / Precision Cams Vanguard Profile - New for 2016!
« on: January 17, 2016, 10:54:33 PM »
Precision Cams has a new Vanguard profile bringing you more speed for the new year.
Available for the solid cast, or new billet camshafts.

Any questions contact:
Mike Edwards
910-251-0612
precisioncamspower@gmail.com

9
Briggs OHV & Vanguard / Re: EC Cam vs Cheetah
« on: December 01, 2014, 12:17:43 AM »
I love this forum, its a big help to everyone building mowers.  I wish we had more time to post more.  I just wanted to clarify a few things and give some of my opinions.  We no longer grind our Cheetah profile for the single Briggs unless the customer asks for it specifically.  We have been grinding our 440 profile for around 3 years because it makes more power.  As far as Cast cam vs. Billet cam, I can tell you we have manufactured thousands of cast cams over the last 32 years with almost zero failures or problems.  In most cases I can get the weight of the cast the same as the billet, in some cases I have got it much lighter.  My cam grinder does not care, but I will say I have many more problems with Billet cams with lobe wear.  Almost all Billet cams have a hard facing weld down the center of the lobe to prevent this.  Almost all Billet cams will wear the lobes without the hard facing weld, which my not be visible with the eye.   

10
Coffee Shop / Re: WONDERFUL DAY
« on: September 22, 2011, 01:13:42 AM »
George I wanted to thank you for all the help you have given me over the years and I enjoy your posts.

11
Coffee Shop / Re: WONDERFUL DAY
« on: August 30, 2011, 10:30:56 PM »
George I really liked 8-23.  Great job!

12
Briggs OHV & Vanguard / Re: Anybody seen the new briggs 33 ci engine
« on: July 18, 2011, 11:01:46 PM »
Precision Cams now stocks the 33 kit engine.  It comes complete with a new PC 440 cam/spring package and all Billet parts.  We also handle all the machine work, making it real easy for the engine builder.   :woo:

13
Briggs OHV & Vanguard / Re: ELS 23hp OHV
« on: May 28, 2011, 09:40:18 AM »
We port and flow these heads all the time.  We can cut them too.  Give me a call if you would like us to help.
Mike at PRECISION CAMS 910-251-0612

14
PRECISION CAMS stocks Adjustable Length Aircraft Aluminum Billet Pushrods for Single/Twin Intek and all Vanguard engines.
Much lighter than the chrome moly push rods!

15
Briggs OHV & Vanguard / New Billet Cams from Precision Cams
« on: May 27, 2011, 11:58:52 PM »
  New PC-440 grind for the Intek Single Billet Cam.
  Same day shipping available on both Single and Twin Billet Cams.

Pages: [1] 2
anything