1
Trannys / Axles / Wheels / Re: EC ft axle assembly
« on: November 09, 2018, 12:18:01 PM »
I will take $250.00 shipped to the lower 48.
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
2
Trannys / Axles / Wheels / Re: EC ft axle assembly
« on: November 06, 2018, 09:01:22 PM »
I P.M. you.
3
Briggs OHV & Vanguard / Re: intec single
« on: November 05, 2018, 12:21:57 PM »
Let us know what you find!
4
Briggs Flathead / Re: Don's motor 101 dvd?
« on: November 05, 2018, 12:15:37 PM »
He does have a OHV dvd? I didn't know that. Check out his Facebook page, there is info on him there.
6
Trannys / Axles / Wheels / Re: EC ft axle assembly
« on: November 01, 2018, 11:41:33 AM »
Any offers?
7
Briggs OHV & Vanguard / Re: intec single
« on: October 31, 2018, 06:47:02 AM »
You could have sheered the key for the crank gear. When you pull it apart make sure you pull off the gear to check.
8
Briggs Flathead / Re: Counter weights
« on: October 29, 2018, 12:34:33 PM »
I have said it before "we need a like button"!
9
Trannys / Axles / Wheels / EC ft axle assembly
« on: October 28, 2018, 02:06:40 PM »
I have a brand new EC front end. It is complete axle nut to axle nut. It has never been installed. It is $325 new, I would like to get $275 shipped, in the lower 48. I take paypal. If you would like pics send me a number to send them to. Thanks AL
10
Briggs Flathead / Re: Don's motor 101 dvd?
« on: October 28, 2018, 01:35:48 PM »
If you can't get ahold of him I might be able to help.
11
Want To Buy / Who Has It? / Re: Looking for some rims/tires
« on: October 03, 2018, 11:40:44 AM »
Did you ever find anything?
12
Briggs Flathead / Re: Adding power to opposed twin?
« on: October 03, 2018, 11:34:41 AM »
My suggestion is look in the flathead briggs section. There is a lot of build information on the oppy. You may have to go back a ways.
13
Newcomers / Re: Hechinger build
« on: August 02, 2018, 10:59:39 AM »
Go to the build section and see George's 07 build. That should help with chassis and steering.
14
Briggs Flathead / Re: Do 28CI Horizontal Flatheads exist?
« on: August 02, 2018, 10:56:36 AM »
They sure do! How many do you want! I have everything for them!
15
Briggs Flathead / Re: Need help w/ cylinder head
« on: July 14, 2018, 01:05:55 PM »
When building a flathead you need to remember compression is not as important as flow! when you port a flathead just clean up the ports, no need to make them bigger. If you go Way back in the flathead section you WILL learn a lot about the flathead. Just doing a good valve job and cleaning up the ports will make a big difference on how well it will run. B&S goes by cubic inches not horse power. The 28ci goes by 12, 12.5, and 13 horsepower. The 11hp or 25ci head will raise compression but folks will debate on whether or not it helps. Some depends on what else you do, cam, carb, ports, flywheel and so on. Yes the lighter aluminum flywheel will add performance! GOOD LUCK with your build!