Heymow - Lawnmower Racing Forum
For Sale => Misc. Racing Items => Topic started by: George Herrin on April 11, 2008, 12:33:31 am
-
(http://i48.photobucket.com/albums/f232/GeorgeHerrin/header_bg.jpg)
EC DISTRIBUTING
2950 HWY 48 SOUTH
DICKSON TN.
PH.615-446-6807
FAX 615-446-9418
UNDERSTAND PRICES LISTED ARE SUBJECT TO CHANGE WITHOUT ANY NOTIFICATION HERE. Check website for the latest on parts and prices. www.eccarburetors.com
(http://i48.photobucket.com/albums/f232/GeorgeHerrin/th_P1010062.jpg) (http://i48.photobucket.com/albums/f232/GeorgeHerrin/P1010062.jpg)
(http://i48.photobucket.com/albums/f232/GeorgeHerrin/th_P1010065.jpg) (http://i48.photobucket.com/albums/f232/GeorgeHerrin/P1010065.jpg)
EC DISTRIBUTING universal front axle assy fits many applications. Was designed for a direct fit for MTD and Murray wide body chassis. Will build to your specifications. Complete axle as you see it above 16" center beam works with 6x6 to 6x7.25 rims. Axle pictured above is with the very new billet spindles.
FCRP-4058 As pictured above less front hubs 245.00
FCRP-4058-1 As pictured above With front hubs 265.00
(http://i48.photobucket.com/albums/f232/GeorgeHerrin/th_P7150415.jpg) (http://i48.photobucket.com/albums/f232/GeorgeHerrin/P7150415.jpg)
Rear 4 on 4 billet aluminum hubs complete with hardware.
FCRP-4074 3/4" axles 30.00ea.
FCRP-4075 1" axles 30.00ea.
FCRP-4076 1-1/4" axles 30.00ea
(http://i48.photobucket.com/albums/f232/GeorgeHerrin/th_P7070405.jpg) (http://i48.photobucket.com/albums/f232/GeorgeHerrin/P7070405.jpg)
(http://i48.photobucket.com/albums/f232/GeorgeHerrin/th_P7070407.jpg) (http://i48.photobucket.com/albums/f232/GeorgeHerrin/P7070407.jpg)
First picture is ground side Second picture is engine side will have a steel center hub with with a 1/4 5 hole blot pattern and two set screws. Designed to be able to remove the pulley yet leave hub in place.
The trans/transzxle pulley's will be all aluminum including hub and all one piece.
BILLET ALUMINUM BILLET PULLEYS
FCRP-4071 8" motor puley Price $59.95
FCRP-4072 6" motor Pulley Price $59.95
1" bore hub with mounting hardware for 8" and 6" pulleys Price $18.95
FCRP-4077 5" trans/tranny pulley Price $49.95
FCRP-5078 4" trans/tranny pulley Price $42.95
(http://i48.photobucket.com/albums/f232/GeorgeHerrin/th_P1010004.jpg) (http://i48.photobucket.com/albums/f232/GeorgeHerrin/P1010004.jpg)
Pictured is a walbro on a 12 hp Briggs engine this is our Dominator series carbs. We have these ready on the shelf along with a tecumseh carb for the 8 HP and for the V-twins. specify which engine when calling. We will build a carb to your engine call for pricing.
Walbro Briggs Dominator 239.00ea.
Tecumseh Dominator 239.00ea.
Cutom built carbs call for Pricing
(http://i132.photobucket.com/albums/q40/BTMRA/th_4070K.jpg) (http://i132.photobucket.com/albums/q40/BTMRA/4070K.jpg)
FCRP-4070K Billet Clutch assy. complete with
belt giudes and mounting hardware 129.00
(http://i126.photobucket.com/albums/p102/georgeherrin2/th_Walbroadjustingneedleforhighside.jpg) (http://i126.photobucket.com/albums/p102/georgeherrin2/Walbroadjustingneedleforhighside.jpg)
This is the needle kit we sell in order for you to make your high side adjustable. $10.00
(http://i126.photobucket.com/albums/p102/georgeherrin2/th_TecumsehsingleorV-twincarb.jpg) (http://i126.photobucket.com/albums/p102/georgeherrin2/TecumsehsingleorV-twincarb.jpg)
This is our tecumseh single or v-twin carb single comes with match airfilter adapter. These are massaged for optimum flow and jetting is changed. Want different jets to experiment with ask. They only fit the EC built carbs. 239.00 ea.
(http://i126.photobucket.com/albums/p102/georgeherrin2/th_TecumsehsinglecarbfilterAdapter.jpg) (http://i126.photobucket.com/albums/p102/georgeherrin2/TecumsehsinglecarbfilterAdapter.jpg)
Fits carburetor in above picture 12.95
316VS Briggs Walbro filter adapter 12.95
641 K&N 10* Air Filter for the above adapters 14.95
(http://i126.photobucket.com/albums/p102/georgeherrin2/th_TechumsehAirfilterAdapter.jpg) (http://i126.photobucket.com/albums/p102/georgeherrin2/TechumsehAirfilterAdapter.jpg)
Fits the Tecumseh V-twins. comes with mounting bolts 42.95
(http://i126.photobucket.com/albums/p102/georgeherrin2/th_Vangaurdfilteradapter.jpg) (http://i126.photobucket.com/albums/p102/georgeherrin2/Vangaurdfilteradapter.jpg)
Fits the two barrel Vanguards and most other brands that use the
two barrel carbs 42.95
(http://i126.photobucket.com/albums/p102/georgeherrin2/th_Airfilterfitsvangaurdandtecumsehtwi.jpg) (http://i126.photobucket.com/albums/p102/georgeherrin2/Airfilterfitsvangaurdandtecumsehtwi.jpg)
Fits Filter adapters FCRP 4056 and 4057 (both twin Filter adapters 42.95
(http://i48.photobucket.com/albums/f232/GeorgeHerrin/th_P1010064.jpg) (http://i48.photobucket.com/albums/f232/GeorgeHerrin/P1010064.jpg)
This is our new hub and sprocket sets for the 700 or any tranny using the 32 or 9 spline shafts.
FCRP-4084 31 spline hub $19.95
FCRP-4085 9 spline hub $21.95
FCRP-4086 12 tooth sprocket $17.95
FCRP-4087 13 tooth sprocket $17.95
FCRP-4088 14 tooth sprocket $18.95
FCRP-4089 15 tooth sprocket $18.95
FCRP-4090 16 tooth Sprocket call for pricing Now available
FCRP-4091 17 tooth Sprocket Call for pricing NOW Available
Turf Pro rear tires 16x7.5x8 .
Turf Master front tires 13x6.5x6 25.00ea.
Turf Master 16x7.5x8 4ply rear tires in stock call for pricing, I don't remember....
True roll 6.5x6 Aluminum 3 bolt front rims .
True roll 7.25x6 Aluminum 3 bolt front rims .
Here is the single OHV rockers, 175.00 a set and are ready for shipment. ;D just in time for CHRISTmas orders. .
(http://i48.photobucket.com/albums/f232/GeorgeHerrin/th_P1010127.jpg) (http://i48.photobucket.com/albums/f232/GeorgeHerrin/P1010127.jpg)
(http://i48.photobucket.com/albums/f232/GeorgeHerrin/th_P1010126.jpg) (http://i48.photobucket.com/albums/f232/GeorgeHerrin/P1010126.jpg)
Here is the roller rockers mounted in an INTEK V-Tiwn. These are ready to go. 300.00 for a complete set.
The Vanguard are ready also look the same But I have no motor here at the time to show them installed. They too will be 300.00 for a complete set.
(http://i48.photobucket.com/albums/f232/GeorgeHerrin/th_P1010125.jpg) (http://i48.photobucket.com/albums/f232/GeorgeHerrin/P1010125.jpg)
(http://i48.photobucket.com/albums/f232/GeorgeHerrin/th_P1010124.jpg) (http://i48.photobucket.com/albums/f232/GeorgeHerrin/P1010124.jpg)
We have our own line of Sprockets from 42 to 50 in two teeth increments, #40 pitch split aluminum fits our new 1 1/4hub and all our goodies are now anodized red as you can see.
Pt# 501 Hub 27.50
PT# T5315-(# of Teeth) Sprocket starting at 26.00 and up.
(http://i48.photobucket.com/albums/f232/GeorgeHerrin/th_P1010131.jpg) (http://i48.photobucket.com/albums/f232/GeorgeHerrin/P1010131.jpg)
Below is the new air filter system for the intek v-twins. You have the one billet turn up it replaces the plastic turn up on the front of the carb then it uses the vanguard adpater and filter. Total price for the whole kit 148.90. Some mods are required to the shroud area.
(http://i48.photobucket.com/albums/f232/GeorgeHerrin/th_P1010133.jpg) (http://i48.photobucket.com/albums/f232/GeorgeHerrin/P1010133.jpg)
(http://i48.photobucket.com/albums/f232/GeorgeHerrin/th_P1010134.jpg) (http://i48.photobucket.com/albums/f232/GeorgeHerrin/P1010134.jpg)
Here is out T-Shirts $7.00 ea. The Ec logo on front and a picture of the back logo...
(http://i48.photobucket.com/albums/f232/GeorgeHerrin/th_P1010056.jpg) (http://i48.photobucket.com/albums/f232/GeorgeHerrin/P1010056.jpg)
(http://i48.photobucket.com/albums/f232/GeorgeHerrin/th_P1010057.jpg) (http://i48.photobucket.com/albums/f232/GeorgeHerrin/P1010057.jpg)
Thanks to TIM RAGSDALE for being our Model.... That got him a free T
Front brakes designed to fit our front axles or any axle with a 5/8 stud simply machine a 3/16 keyway and tighten set screws. Brakes come as you see them in the picture. Brake line and master cylinder is seperate due to the many different applications and trying to save the race a dollar. Price for complete set is 420.00. That both sides. 60 cheaper than the Hegars.
(http://i132.photobucket.com/albums/q40/BTMRA/th_1001.jpg) (http://i132.photobucket.com/albums/q40/BTMRA/1001.jpg)
(http://i132.photobucket.com/albums/q40/BTMRA/th_1000.jpg) (http://i132.photobucket.com/albums/q40/BTMRA/1000.jpg)
Transaxle brake hat, machined for 1"axle but will also have a sleeve you use for a 3/4 inch axle. Don't have a price on it yet.
(http://i48.photobucket.com/albums/f232/GeorgeHerrin/th_DVC00311.jpg) (http://s48.photobucket.com/albums/f232/GeorgeHerrin/?action=view¤t=DVC00311.jpg)
(http://i48.photobucket.com/albums/f232/GeorgeHerrin/th_DVC00312.jpg) (http://s48.photobucket.com/albums/f232/GeorgeHerrin/?action=view¤t=DVC00312.jpg)
(http://i48.photobucket.com/albums/f232/GeorgeHerrin/th_DVC00313.jpg) (http://s48.photobucket.com/albums/f232/GeorgeHerrin/?action=view¤t=DVC00313.jpg)
Below is the EC transmission As you can see it is a mower transmission. Price not set yet soon as we get them will let you know. I have been hammering on this one have 7 to 10 races so far, Jake has dropped the clutch till he got tired and quit and have yet to do any damage. But here is what they look like.
OK the transmissions are IN race ready add oil and go no reverse Standard 5 speed transmission Steel input and bevel gears thrid gear is 25/25 gear set. THESE ARE NOT PEERLESS. They ARE a direct replacement.
(http://i48.photobucket.com/albums/f232/GeorgeHerrin/th_P1010515.jpg) (http://s48.photobucket.com/albums/f232/GeorgeHerrin/?action=view¤t=P1010515.jpg)
(http://i48.photobucket.com/albums/f232/GeorgeHerrin/th_P1010517.jpg) (http://s48.photobucket.com/albums/f232/GeorgeHerrin/?action=view¤t=P1010517.jpg)
(http://i48.photobucket.com/albums/f232/GeorgeHerrin/th_P1010514.jpg) (http://s48.photobucket.com/albums/f232/GeorgeHerrin/?action=view¤t=P1010514.jpg)
MORE TO COME AS TIME PERMITS
-
We now have the 12hp copper head gaskets back in stock. .032
We also have neck braces and driving gloves.
Call for pricing.
-
We now have Moly Push rods for those motors using the small diameter push rods, these are 1/4 od hollow chrome molly they come in kit form 4 rods 8 tips cut rod to size insert tips . 53.00 and change. Not sure of exact price. These fit the vanguard and intek twins, We are going to also have the larger diameter rods for the single briggs and Tecumseh twins soon.....
-
We now have copper 28 ci ohv head gaskets available can be lightly trimmed for 31 also. I believe the pricing is 24.00 do not take this as an exact price, I do not know as of yet.
-
We now have front Brakes available.. Look above for Pictures and info
-
Finally racers those with the Billet pulley's when you wear them out don't toss em send them in to be re-furbished. We now have the tool Finally to allow us to simply chuck it on the lathe go in face the V and like new. Only makes them about an 1/8 smaller.
-
Ec has a new AXLE coming out for the ARMA new Super Mod classes. For a picture of it
http://www.eccarburetors.com/store/index.php?main_page=popup_image&pID=2236
-
EC now has springs part#260 in stock just came thru the door. We will fill back orders as quickly as we can.
-
EC now has copper head gaskets for the Tecumseh V-twin part# 2202 19.80 ea. They are .032 thick.
-
We are out of 700's distributors are out we have also been told upon availability there will be a substantial price increase. Now for those waiting on transmissions, we can order them but they will be 275.00. OR if you can wait we will be having our own by the end of Febuary. If you can wait till then these should be priced at 200.00 or maybe even a bit less. They will have steel gears and the cases will be beefier. All parts will be interchangeable with the peerless parts except the splined shaft and gearsand Input gear and bevel. BUT all peerless parts can be transplanted into these cases. We will have transmissions and all replacement parts here towards end of Febuary. SO thats the lowdown on transmissions at this time. We are trying to help you the racers and keep the prices affordable. Some of you know and have seen them on my mowers I have been testing them. I have yet to break one. Absoluteky no leakage whatsoever. These aare some good units. I like them allot so far. In fact they were in my mowers at the ALL American. Thats where we stand right now.
-
Folks our jack shaft for those using the transaxle setup should be ready to go by the end of the week. Billet aluminum housing with high speed 3/4 bearings and ends of the 4140 shafts are turned down to 5/8 keyed and drilled and tapped for a bolt for pulley retenion. Will come with a 1/4 thick 13" wide C channel mount plate ALSO. Will post pictures as soon as they are done.
-
Transaxle brake hat pictures are posted scroll up to see them in the picture section
-
SCROLL UP Added a couple pictures of the EC transmission. This is the one I have been testing (trying to Break) and have yet to hurt anything. Expected arrival is March 10th. Thats EXPECTED arrival. Do not have a set price yet not till they arrive with invoices
-
EC TRANSMISSIONS ARE IN AND RACE READY they come with no grease just add 8oz of oil and go they have no reverse...standard 5 speed ...Steel input and bevel gears...third gear is 25/25 gear set...two key shafts. We have all the replacement parts for these transmissions also. They are a direct replacement for the peerless transmssions. 200.00 IS YOUR COST PLUS SHIPPING.
We have transmission case's hope you saved your broken peerless transmissions you can rebuild then using these cases. Top and bottom case both for 50.00 for the complete case set top and bottom. Sold as a set only. We will not seperate.
(http://i48.photobucket.com/albums/f232/GeorgeHerrin/th_P1010515.jpg) (http://s48.photobucket.com/albums/f232/GeorgeHerrin/?action=view¤t=P1010515.jpg)
(http://i48.photobucket.com/albums/f232/GeorgeHerrin/th_P1010517.jpg) (http://s48.photobucket.com/albums/f232/GeorgeHerrin/?action=view¤t=P1010517.jpg)
(http://i48.photobucket.com/albums/f232/GeorgeHerrin/th_P1010514.jpg) (http://s48.photobucket.com/albums/f232/GeorgeHerrin/?action=view¤t=P1010514.jpg)
-
EC has some new parts for those using the 820 transaxle's. I have converted the brochure into a jpeg so you all can see it. Click on thumbnail.
(http://i48.photobucket.com/albums/f232/GeorgeHerrin/th_ecbrochure.jpg) (http://s48.photobucket.com/albums/f232/GeorgeHerrin/?action=view¤t=ecbrochure.jpg)
-
"31-30 EC Thunder Stix" New all Billet tool steel core fits Briggs model 31 OHV cam for mower racer. This cam pulls like hail. a lot of testing went into this cam it is all new cam profile design for this engine, not a copy off something else. With our roller rockers specs are: intake lift .467 duration@.050 257 C/L 105 exhaust lift ....473 duration@ .050" 261 C/L 111 price at $175.00
(http://i48.photobucket.com/albums/f232/GeorgeHerrin/th_31-30Thunderstix.jpg) (http://s48.photobucket.com/albums/f232/GeorgeHerrin/?action=view¤t=31-30Thunderstix.jpg)
-
do the gear boxes have bearings or bushling?
-
bearings on input shaft bushings on the other shafts
-
EC now has Diatech Dirty Harry hand throttles for your steering wheels in stock.
-
what price are they?
-
Don't know all I know is while I was up there Friday for awhile they come in.
-
George, Is the 31-30 cam for the avs motor ? If not how will it work in a 28" motor? Thanks Gary
-
Its for all the single ohv motors
-
:confused: is this a good JP /SS/Imow Cam :confused:
-
:confused: is this a good JP /SS/Imow Cam :confused:
:rofl:
-
Sure Barry throw it and go
-
under arma and i believe us you cant do that. :bash:
-
That's only if you get caught...
Just saying...
-
under arma and i believe us you cant do that. :bash:
Barry CAN!!!!
-
:doh: :doh: :lol: WHATS THE OLD SAYING? GIVE EM 9 THINGS THAT THEY CAN FINDE AND THE 10TH THEY WONT SEE? :badgrin:
-
:doh: :doh: :lol: WHATS THE OLD SAYING? GIVE EM 9 THINGS THAT THEY CAN FINDE AND THE 10TH THEY WONT SEE? :badgrin:
Unkless you publicly announce your intentions some where??
LOl
SHHHHHHHHHHHHHHHHHH
-
be very quiet, im hutin wabbits. :lol:
-
Sure Barry throw it and go
Thanks.
Will Getter Done. :D
-
EC now has he 2201 COPPER headgaskets for the Briggs single OHV back in stock for those waiting.
-
We are now selling Hoosier grooved racing tires. WE have 11x5.5x6, 12x8x6, 12x9x6 and 15x8x8 all medium compound call and ask for Tony for pricing or check the website if not there will be added shortly.
-
ON SALE NOW
Quick CAR air gauges 0-20 pt# 56-020 and 0-40 pt#56-040 both sale for 30.95 and are on sale for 20.95 while supplies last. Want to see them go to our website and type in the pt# in the search.
-
George is the price on the turf master pro tires 16/7.50/8 are they 22.50 like it says or are the more also do y'all have 8" rear Douglas wheels in stock
-
not sure where your seeing 22.50 They are 73.97 http://www.eccarburetors.com/estore/index.php?main_page=product_info&cPath=19_76&products_id=2244
Also we do not carry Douglas wheels anymore we have a 8x8 wheel like a satin finish or brushed aluminum look
-
Page 1 that's what the price is out next to them just checking sounded cheap also might wanna check that out can u get them mounted with tubes my luck with tubes here lately hasn't went well
-
I took the price off the Turf Pros on page one, and deleted the line where it says douglass 8 x 8 wheels.
-
George is the price on the turf master pro tires 16/7.50/8 are they 22.50 like it says or are the more also do y'all have 8" rear Douglas wheels in stock
There is no "Turf Master Pro"
There is "Turf Masters" or "Turf Pro's" , 2 different tires!
"Turf Pro's" used to be $22.50 at EC...3 years ago, lol!
Since then the tires have been discontunued by Carlisle.
-
ALL PRICES POSTED HERE are subject to change without any notice here so please check EC website or call for up to date pricing.
-
Quick question with the ec tranny are the replacement gears and parts i get from my local tecumseh dealer compatible with that tranny? just wondering before i spend the money :confused:
-
Only the parts/gears off the brake shaft ( the one with the shift keys) are interchangeable the shaft with the splined are different splines and input and bevel are different however all Tecumseh parts can be put in it if you wanna replace it all
-
EC now has intel twin copper head gaskets for 19.00 each in stock .030
-
EC now has intel twin copper head gaskets for 19.00 each in stock .030
For all 3 cubes?
Lester
-
Initially it's a 40 and can be trimmed to fit the 44 n 49 trying to keep
Costs down for you guys
-
how much is the dirty harry throttle levers?
-
Initially it's a 40 and can be trimmed to fit the 44 n 49 trying to keep
Costs down for you guys
Is there a photo of it? The 49 is a different shaped gasket. It is fully round near the push rod pocket where the 40 and 44 are straight across.
Lester
-
OK FOLKS EC has the NEW and improved WEB SITE/STORE up and running. The old site will be taken down so change your favorites and this new link http://www.eccarburetors.com/store/ ALSo if you see any graphics or tags that have an X in its place be sure your java is up to date and the site also works best using I.E. 8 or later....
-
Looks great and a barn yard better than the old site!
MUCH easier site to navigate!
:+1: EC!
Found an issue, sent a message, lol.
-
We know we will have some glitches PLEASE if any of you see any please by all means send an email with the problem to sales@eccarburetors.com WE HAD t to go to this new site a bit quicker than we anticapated. We appreciate any and all emails and comments on the new site.
-
EC now has black plastic kart seats for the super mod builders. If you have ever seen a shifter kart these are designed to hold you in the up right position. They have deeper butt pockets to hold you comfortably no matter the direction your moving in. Price is 89.95 and we only have xl at the moment. Stayed tuned as we add to the super mod line of products
-
Went to your new web site !!!!!!! VERY NICE JOB WELL DONE
-
THANKS
For those allowed to run them and the FXS AND FXT and the Super Mod GUYS we now have nerf bars and front bumpers. Our first ones went out today, not sure if they are on the site yet but will be soon.
-
EC complete front brake kit Pt #1009 comes with left and right brake assemblies 10ft of brake line, 4oz of brake fluid, Master cylinder, and a mechanical Bias Control everything you need all for 563.55 While supplies last.
-
The t-shirt pricing, when you click onto 2x it doubles in price, is this correct? If it is, ok, but the last time I ordered one I think it added $2?
-
Fixed
-
The t-shirt pricing, when you click onto 2x it doubles in price, is this correct? If it is, ok, but the last time I ordered one I think it added $2?
2X=DOUBLE. :lol: :lol: COULDNT HELP IT AL.
-
2X=DOUBLE. :lol: :lol: COULDNT HELP IT AL.
Thanks for the chuckle John!! :lol:
Fixed
Thank You George, Gives me a reason to get more other stuff!!
-
George. on those high idle adjustment screws, is there anything that needs to be done to the carb, or just put in, adjust, and go?
Lambo
-
If you bought the kit, 100-506k it came with needle and correctly modified nozzle just install and go. IF not then it may need some work done OR if you have a carb with a small jet in side of aluminum down tube remove it and install needle and it will work fine. TUNE to run.
-
Thanks. So basically I need to make certain the needle fits inside the tube..if it doesn't, remove the small inner jet,or I assume I can drill out the down tube carefully?
Lambo
-
EC now has intel twin copper head gaskets for 19.00 each in stock .030
George what is the stock thickness of the head gaskets on the intek twins?
-
about the same once crushed
-
Ok awesome thanks, So these are the way to go for high compression motors instead of the older fiber gaskets.
-
yup...
-
Great thanks ill call tomorrow for a order.
-
Go to a bicycle shop. It's a standard part there.
-
FOR THOSE WAITING TRANSMISSIONS ARE IN
-
Yea.. got a friend that's gonna be one happy camper
-
EC DISTRIBUTING now has STEEL Ring gears for the ARC Briggs single flywheels and also the ARC VANGUARD flywheel. Price is 70.00ea. call while supplies last.
-
I hope one comes available for the gx390 and the intek twins!!!
-
the intek Not sure about anything else.
-
EC now has the steel ring gear for the briggs singles and Vanguard V-twin flywheels which will now come on those flywheels when you buy them now. No change in price meaning they will be the same price as always. So buy a new flywheel from us they come with the steel gear. These ring gears were designed in an effort to help the racers with less wear and the ability to use the aftermarket starters available. Our testing here the aftermarket starters have worked great with the steel ring gears with their harder engagement. Being able to use the aftermarket starters will also save you the racers on average 100.00 or more over the briggs starters. These are race parts and as always their is no warranties expressed or implied on race parts.
Again they are presently available for the BRIGGS SINGLE flywheels and the Vanguard Twin Flywheels.
-
DO YOU HAVE ANY FOR THE 28 OR 19'S?
-
Not the 19's but it fits the Briggs singles which cover ALL f/h to ohv from 12hp to 20
-
REAL GOOD TO KNOW!
-
THANKS. 8)
-
EC NEW 4 DISK Clutch is now available. Proven and tested in house for a full season by myself and Jake. Its the disk clutch you have seen on Jakes machine. Easy to adjust. Only in 1" bore comes with your choice 35 sprocket 18 or 14 tooth and 40 sprocket 13 tooth. Sales for 389.00
(http://i48.photobucket.com/albums/f232/GeorgeHerrin/th_4disc_clutch_zpscd8bb93a.jpg) (http://s48.photobucket.com/user/GeorgeHerrin/media/4disc_clutch_zpscd8bb93a.jpg.html)
-
Is the sprocket replaceable, if so what's the cost.
-
Yes I am not sure of the cost but will find out.
-
EC just got transmissions in for those waiting we got em.
-
Our 31-30 OHV Briggs Single Billet cams are now in stock for those waiting.
-
Ok some have experienced lifter failures in the Briggs twin motors we have the fix for this. EC now sells billet lifters for the INTEK, and VANGUARD V-Twins. They just come in so not sure on pricing, but give Carroll A CALL AND HE CAN FIX YOU UP.
-
ec no longer has oppy stuff :bash:
-
never sold anything
-
well that sucks. was planning an oppy build just needed rods and pistons anyways. just noticed they took the oppy stuff off the web site.
-
Call Carroll will order it
-
ok thanks George
-
We made a video. We've had some questions about finding things on our website and about our shipping system. We get questions like these just about everyday so we made a video to answer most of those questions. This will hopefully become a regular thing for us so if there are any question that you need a video explaination for you can ask here on the forums, our facebook page or contact us through our website. We will try to make videos as quickly as our time allows.
https://www.youtube.com/watch?v=kxjEdheuMNU
-
George looking for info on 2bbl carbs. Price levels and what's done to them? Kohler preferred and the big block Kohler carb. Also looking g for the generac big block carb with the same throttle hookup as the kohler.
-
we do not have the kohler stuff or genrac. And they are bigger than ours. Ours off the shelf are bigger than stock vanny or intek carbs. They can be mad a bit bigger. prices off the shelf are 295.00
-
BLACK FRIDAY DEALS are UP! Over 50 items are discounted including 420cc clones for $300, 4-Disc Clutch for $350 with 13 tooth #40 Driver. And much more. All order must be made online before Tuesday Dec 1st at 8am CST to receive discounts.
http://eccarburetors.com/store/en/black-friday-deals.html
-
Have any Walbro 100-506 for $10 in stock ?
-
Jake
Your best bet is to call them directly.
This topic hasn’t been posted in since 2015......
George, who took care of this post is no longer with us. And I doubt anyone from EC is following this thread.
Paul
-
Have any Walbro 100-506 for $10 in stock ?
I,m sure EC probably has Walbro 100-506 in stock and its $39.95 plus shipping,100-506 is obsolete now.EC makes their own and it comes as a kit with the correct,nozzel(emulsion tube).
-
The part number at EC is 100-506K