Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - badboysracing

Pages: [1] 2 3 ... 11
1
Coffee Shop / Re: WONDERFUL DAY
« on: September 10, 2012, 09:13:53 am »
well today would be a wonderful day but here in prentice, wi it is the first day back to school after the tragic loss of town amazing girls which were juniors in high school. When i was in school it didnt matter who you hunt out with they would always talk to you. They were great all around girls and there life was cut short in an auto accident friday night,

2
farthest i have been up to Door County Wi for a Badger State race and then left there and headed for Oshkosh Wi which was the next day and is about the same distance from here and that was 4.5 hours.

3
Coffee Shop / Re: Introduce Yourself!
« on: November 14, 2011, 10:02:08 pm »
Name: Brian "Butchy" Gullickson
age: 19
years racing: 7
mower: sears lt-10 aka the war horse. has been in racing for 9 years now.
interesting fact's: going to attend college to become a certified welder. spend my spare time fishing and hunting, and riding atv.

4
Briggs Flathead / Re: single flathead cube ?
« on: September 27, 2011, 09:54:28 pm »
My good buddy in racing had one done and it held up good other than the fact that the outfit that milled off the top of the piston milled it at an angle resulting in the block cracking on one side. but man it was one heck of a torque monster and untouchable by any other single.

5
Garden Tractor Pulling / Re: Thinking of getting into it...
« on: August 21, 2011, 08:58:18 pm »
Randy where is the pull on the 27th at. may have to just go watch it

6
your welcome

7
to me it just looks like the engine wearing ins still. i wolud run it for a few hours change the oil again and do that once more then it should stop with the flakes like that.

8
Post your Pics! / Re: Receding Rim
« on: July 12, 2011, 09:10:52 pm »
around here in northern wisconsin it's mostly red clay.

9
Coffee Shop / Re: Got accepted into college
« on: May 19, 2011, 07:44:06 pm »
i am graduationg from high school may 28th and i start a semester long program for 5 hours a day to become a certified welder in the spring of 2012. gonna be great. I will be attending Northcentral technical college here in wisconsin. Phillips campus and it is only about a 12 mile drive for me one way.

10
Racing Mower Builds / Re: Rooster Cruiser '09 Edition!
« on: April 17, 2011, 08:41:07 pm »
the best chain tensioner i have seen is a home mad one out of aluminum with skate board wheel bearings in it. work's great and candle the power of the built twin without a problem

11
Chassis / Re: chassis for b/p
« on: March 09, 2011, 07:58:46 pm »
i'd be different and build the husqvarna because almost no-body builds them

12
Coffee Shop / Re: Other Hobbys
« on: February 13, 2011, 10:12:33 am »
mine are hunting, fishing, and ridin atv.

13
Garden Tractor Pulling / Re: Thinking of getting into it...
« on: January 09, 2011, 08:10:30 pm »
Randy is there a junk yard close to you. Most junk yard's also have a higher poundage scale that has to be checked by the dot so if there are any close i'd go there to get it weighed.

14
Chassis / Re: Billet Caliper???
« on: December 21, 2010, 09:27:45 pm »
while you guy's dont think the mini lite will do good. I know they will work fine. i run one on my mower and it will lock up the tires at any time just like the std size one will.

15
Briggs Flathead / Re: billet flywheels
« on: October 05, 2010, 09:51:37 pm »
paul that all depends on the motor you have too. I know fo someone here in wisconsin that had a competitive a/p with the cast flywheel just gotta know how to run the mower with that flywheel.

Pages: [1] 2 3 ... 11