Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Topics - GTX21

Pages: [1] 2 3
1
Briggs OHV & Vanguard / Vanny vtwin 14hp stock cam spacer
« on: February 17, 2013, 11:40:23 am »
I've searched on hear and read about a spacer that needs to be made in order to maintain oil pressure on a bare no governor stock vanguard twin cam. I've removed everything on the cam, it's now hollow. I just don't understand what the spacer is suppose to look like and the best way to do it. A picture of this spacer would help a bunch!

2
Driveline / Peerless 350 output hub and sprockets
« on: December 01, 2012, 11:50:43 am »
Where can i get the correct splined hub that is able to have the spockets welded on to it for a perrless 350?

3
Driveline / 350 (Im stumped)
« on: December 19, 2010, 05:05:22 pm »
I have my peerless all rebuilt with bearings and seals, its together the way the diagram shows(with reverse removed).
Heres the problem, it will shift into all gears but with only ingage into two of the 3 gears possible(reverse removed).

I dont know the shift pattern but here is what i found
Forward and to the left is 3 to 1
Forward to the right it just spins the input
Back to the right is about 6.3 to 1
Back to the left it just spins on the input.

I cant figure out why it will only engage in them two gears and nothing more. Any suggestions?

4
Briggs OHV & Vanguard / Single 18 OHV AVS vs 14 Vanguard V twin
« on: July 04, 2010, 12:02:19 am »
I wanna know what your guys opinion on this one. Which is better?

5
Briggs OHV & Vanguard / 14 vanguard vtwin
« on: July 03, 2010, 12:42:24 am »
What exactly do the internals in the cam do?(the 2 ball bearings) Some how the one ball fell outta of the cam.

6
Chassis / Opinions on how to setup rear!!
« on: June 11, 2010, 11:01:07 pm »
Ok I been thinking about how i could set up my rear axle on my mtd lawnflite chassis. I was gonna weld some 1 inch square tubing then put pillow blocks on top of that for my axle. This is CP class if that helps. I wanted to know how you guys would do this so I need your opinions.






7
Briggs OHV & Vanguard / Rocker stud torque
« on: January 25, 2010, 06:16:41 pm »
Whats the rocker bolt torque(bolt to head, not the adjustment nut) spec for a 14 vanguard twin?

8
Briggs OHV & Vanguard / Re: Vanguard Intake
« on: January 25, 2010, 05:25:07 pm »
Is it ONLY 20hp intake that will fit on anyother vtwin vanguard to run two barrel?

9
Briggs Flathead / split valve?? Possible??
« on: January 05, 2010, 09:42:13 pm »
Ok, my friend wanted me to ask this, A friend of his claims he has a motor that the valve is split down the center (on the valve head i guess) I sed its not possible, So the question is, IS it?

10
Briggs OHV & Vanguard / 31ci avs
« on: January 04, 2010, 09:44:17 pm »
I got a 31 avs motor and was thinking instead of buying the brass weights would getting the crank balnaced allow me to get rid of the AVS and not have to run the brass weights? This will have a stock cam in it also so im thinking of using the flathead timing gear as I have read that they are weak, preferably which model flatheads timing gear will interchange?

11
Briggs OHV & Vanguard / 14hp
« on: January 04, 2010, 05:36:02 pm »
Okay my buddy has this 14 hp and its a twin, sorta looks like a v twin. How good would you consider that motor? It has one of them electric carbs and seems to be in great condition. It runs to.

12
Chassis / Front Axle Build
« on: October 17, 2009, 05:53:39 pm »
Okay im trying to get all the stuff togther that I need to build a nice adj axle. Since I can get the end plates stamped out for free by a local machine shop I need to know the dimensions of the end plates.

What is the comom width and lenght of the end plates?

Thickness?

For The rest of the axle here is the list i came up with for the stuff I need:

Steel Tubing 1"x2", Wall thickness?
Plate steel (end plates) Thickness???
Heim ends 1/2" or should i go 3/8"

Spindels look like they are hard to make, so I dont know what im gonna do their.

13
Driveline / 3/4 live axle
« on: October 14, 2009, 05:40:41 pm »
How well do you think a 3/4 live axle (i believe its a steel that is used for hydraulic cylinder rods, its chromed) would hold up?Because I have this at the moment but if it wont hold up then ill go 1 1/4. Oh and its a farly smooth track, with an ocassional bump or two.

14
Briggs Flathead / Opposed Rod Caps
« on: October 11, 2009, 09:07:29 pm »
When installing the caps is there a wrong way and a right way to put them on?(orientation) Whats the right way

15
Driveline / Opposed Gearing
« on: October 09, 2009, 12:59:45 pm »
I have a slightly modifed opposed twin. I did everything don shows in his video and Im trying to find out my gearing. Im running a 350 tranny(race prepped) in 2nd gear, which is 4.11. Im running a 6 on the engine to a 6 on the tranny. What should i look for, for the sprockets? The track has farely short straights and medium wide corners. One of the tracks is banked pretty high and the rest are mostly flat. I think the straights are mostly 50 to 80 feet long and pretty wide corners.

Pages: [1] 2 3
anything