Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - stephenson racing

Pages: [1] 2
1
Briggs OHV & Vanguard / Vanguard rods
« on: February 26, 2017, 07:31:52 pm »
Anyone run in to rods to thick to run on crank. Wrong crank or rods?  35 horizontal vanguard with rocket Ron rods. The second rod doesn't have room.  Any help would be appreciated.  Thank you

2
Briggs OHV & Vanguard / Re: Crank shim 35 vanguard horizontal
« on: November 07, 2016, 01:42:43 pm »
Thank you just checking

3
Briggs OHV & Vanguard / Crank shim 35 vanguard horizontal
« on: November 06, 2016, 12:31:24 pm »
Is there supposed to be shim on flywheel side of crank. First vanguard build. Appreciate any help. 

4
Coffee Shop / RE: dirt track opening soon in Rockingham nc
« on: November 14, 2015, 07:53:06 am »
Where's track located. Address. Thank you

5
Chassis / Re: How do I loosen mower up
« on: September 21, 2015, 02:49:31 pm »
Rr is biting too hard causing mower to lift on two tires and I have to get out of the throttle. Don't know what u mean about chassis bind. All my mowers push better going straight because of the straight axle (posi). Always try to stagger tires.  I need back of my mower to slide a little bit entering corner but hook coming off. I know I want a lot but the guy I race (Charles ford) is always hooked up

6
Chassis / How do I loosen mower up
« on: September 20, 2015, 11:19:17 am »
My mower keeps picking up rear tire. More air in rr helped for a few laps but also lost a lot of rubber from spinning coming off corner. I race sp class. Please help. Thanks.

7
Briggs Flathead / Re: Piston exploded
« on: August 17, 2015, 10:55:05 am »
Thanks. Ec doesn't  have forged but still looking.  Ec said they don't have a lot of piston problems

8
Briggs Flathead / Re: Piston exploded
« on: August 16, 2015, 10:16:46 pm »
Yea long rod.  About 6500 to 7000 rpm. Wanted to know if others are using a different piston

9
Briggs Flathead / Piston exploded
« on: August 16, 2015, 08:45:57 pm »
Building another 28ci. Wanted to know if anybody else had problems with using stock 31 ohv  piston. Thank you

10
Briggs Flathead / Re: Walbro carb fuel inlet
« on: January 13, 2015, 03:42:41 pm »
Thanks, didn't want to mess up my favorite carb.

11
Briggs Flathead / Walbro carb fuel inlet
« on: January 13, 2015, 11:01:49 am »
Broke plastic elbow. How do u change it to brass.

12
Tires / Re: Burning rr tire off
« on: September 14, 2014, 04:34:34 pm »
Yea it's at ellerbe just thought it was excessive. I have been running a little more air pressure.  Will try running less thanks

13
Tires / Burning rr tire off
« on: September 14, 2014, 10:42:41 am »
Had mower for about 3 seasons have had rr tire issues the whole time. Would appreciate any input. Ty

14
Chassis / 40 wide
« on: December 03, 2013, 01:43:13 pm »
Just wondering how everyone is getting to 40 wide on old builds

15
Briggs OHV & Vanguard / Re: new 21 intec flywheel problem
« on: March 10, 2013, 11:37:53 am »
thanks everyone took it to rocket ron and he did what docbro  said  THANK YOU ROCKET RON IT WAS STARTIN TO STRESS OUT MY PARTNER!

Pages: [1] 2