Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Topics - Darkviper

Pages: [1] 2 3 4
1
Kohler Engines / cv16 upgrade as roller kohler
« on: August 26, 2015, 02:37:29 am »
I have few questions about my single Kohler. Do u have to run voodoo coils with mwsc flywheel and which cam blank is for a roller Kohler?

2
Briggs OHV & Vanguard / 31 wrist pin hole size is for piston
« on: March 19, 2015, 04:43:00 am »
I'm trying to find what pin hole size is for 31ci single cyclinder thanks.

3
Honda and Clone Engines / billet valve cover problems
« on: January 25, 2015, 02:00:45 pm »
Has anyone experienced this before. Some reason set roller rockers right  and valve cover and the adjustable screws to fit push rods hits the valve cover. I'm runnin 1 to 3 roller rockers.

4
Kohler Engines / 27hp kohler valves
« on: January 12, 2015, 03:18:42 am »
Dose the 27hp Kohler heads have bigger valves then 25hp-18hpv twin heads.

5
Kohler Engines / command head milling
« on: November 17, 2014, 09:59:47 pm »
I never do milling on head before on one of these anyone give me idea how much u can take off with flattop pistions?

6
Honda and Clone Engines / need help with gx390 head gasket problems
« on: October 05, 2014, 07:53:31 pm »
I have blown head gasket problems can't find 92mm copper head gasket any suggestions. The multy laryed won't hold.

7
Honda and Clone Engines / rpms on stick or clay track
« on: July 01, 2014, 08:15:04 pm »
Last weekend I went to iowa did good when it was dusty out but when it was sticky I didn't do so good. I was pushing 5200 rpms. I built this motor with wild cam in it and able to hit 8000rpms with out blowing up. Honestly I don't think my motor was even close to power band when it was sticky im using cheeta grind I think it hits 7500rpms. So I was wondering if that's what im suppost to run for rpms if its wild cam and not a mild cam.

8
Coffee Shop / help calculating gearing on fxs on 10th mile or less
« on: May 05, 2014, 05:35:06 pm »
Need help calculating gear ratio. I'm running 13 to 28 35 chain to 13 to 44 40chain with 8 rims.

9
Coffee Shop / light weight flywheel
« on: February 08, 2014, 10:22:39 am »
Iv been thinking of trying to run one in racing. Question will work I know it be all or nothing good torque and rpm building but bad on the turns any opions on it.

10
Driveline / noram clutch spring choices
« on: January 13, 2014, 11:59:54 am »
I'm running purple engaging at 2500rpms its just like I don't think runs right with it any suggestions what to run or what others are running

11
Tires / Question on D12 hoosiers
« on: September 20, 2013, 05:39:18 am »
I had only 4 races on this mower and 3 of them with stock timing on flywheel. I was running turf masters different kinda tire pattern. After the race when i turned up the timing on flywheel to 3rd mark. I notice my turf tire was almost balled. In the race i was just spinning the tires  basicly sliding for 4 laps into the race then spinned out in the straight away and then my chain poped off. I was surprised i was in 1st place and 5 tractor lenghts ahead of anyone until I spinned out,  So i was wondering if the D12 tires would last longer then turf master tires.

12
Driveline / Long chain on fxs and fxt
« on: August 16, 2013, 03:35:02 am »
I had a problem with having chain poping off the rear sprocket. It keeped pulling the axle forward on quick change rear sprocket side and hitting the fender when you hit the throttle. So we put another bearing and hanger in to help support it but it keeped throwing it still. So i order a chain guard from parsons racing which is the chain guard for quick change rear sprocket and so far its been not throwing chain anymore. I figure this would help to anyone who has or will have same problem.

14
Coffee Shop / Traction
« on: August 04, 2013, 09:16:44 am »
Im having a problem with just spinning tires on my fxs getting little to no traction. Right now im running turf masters on rear tires. Its fully but clone engine but its not building rpms like should be I think because of that problem. Any input how to get to grip more will be helpful thanks.

15
Chassis / Need ideas how to do foot throttle
« on: July 02, 2013, 01:57:19 pm »
I need ideas how to do foot throttle or picture would help a lot thanks for input as in how to make braket to hook cable to paddle.

Pages: [1] 2 3 4
anything