1
Briggs OHV & Vanguard / battery not charging
« on: December 27, 2017, 02:58:53 pm »
I rewired the mower to push button start I ran the charging wire back thru the solenoid it's not charging tho.any advice?
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
2
Tires / Re: tire seating
« on: December 24, 2017, 04:12:25 pm »
They had it I'm just puttin New tires on her .thanks for advice
3
Tires / tire seating
« on: November 14, 2017, 09:02:10 pm »
Front tires went flat from sitting and can't get the bead to seat again. Is the gas and hammer trick safe to do on mower tires?
4
Tires / Re: Skinny tires on front of drag mower
« on: September 28, 2017, 08:52:59 pm »
Less weight . If u have alot of power itll help keep straight ,help alot more if ur running on dirt or clay.new to mowin but been drag racing for many. Im getting my skinnys off the front of the mini pocket rockets and a set off the 50cc chinese dirt bike for the dirt
5
Briggs OHV & Vanguard / Re: mikuni dirtbike carb /governor
« on: September 25, 2017, 05:33:50 am »
I plan on gettin a 33ci when i kill this one but till then i wanna use the 21 its a really strong engine ,i was hoping a 28 0r 31 flywheel would fit . Iv got a walbro i rebuilt instead ov the mikuni so im gonna keep the gov n just bend the tab a lil
6
Briggs OHV & Vanguard / Re: mikuni dirtbike carb /governor
« on: September 23, 2017, 09:46:31 pm »
There doesnt seem to b any for a 21 cubic inch briggs. I thought i had read somewere about a class that could run ungoverned stock flywheel with a scattershield .wonderin if its safe and how often do the ungoved blow up
7
Briggs OHV & Vanguard / Re: mikuni dirtbike carb /governor
« on: September 22, 2017, 09:23:06 pm »
Can't find any arc parts for the 21ci briggs
8
Briggs OHV & Vanguard / Re: mikuni dirtbike carb /governor
« on: September 22, 2017, 04:35:10 pm »
What do I need to do if I take off gov to keep fro blown up engine?
9
Tires / Re: Turf Pro Replacement
« on: September 22, 2017, 04:31:25 pm »
Yea that's what I came to notice .what about the pro 3s how do that match up to the pros?
10
Briggs OHV & Vanguard / mikuni dirtbike carb /governor
« on: September 21, 2017, 09:33:32 pm »
I have a mikuni dirt bike carb I never put on my bike .I seen people put them on mowers and it work out nice, but my question is does the governor still work? If I put the mikuni on with it's own throttle cable will the gov still work ? Do I need a throttle cable to hold the gov arm in the position I want or can it just be uncooked and still work how it's supposed? Sorry bout the long dumb ? .I just don't wanna be completely un goved
11
Tires / Re: Turf Pro Replacement
« on: September 21, 2017, 05:54:57 am »
I know its not a new post but happened to be looking for the same style tire .they have a turf pro 3. The carlisle turf smart tire has a low sidewall
12
Tires / Re: bias ply mower tires/stock tires
« on: September 21, 2017, 05:47:15 am »
Thanks for the answers guys.i had some bias ply on my mustang and couldnt make a turn without losing it. Do the mowers with race tires use tire prep?
13
Tires / Re: bias ply mower tires/stock tires
« on: September 19, 2017, 08:54:55 pm »
True drag slicks r bias tires and they coil up at take off and if u turn at high speed the sidewalls flex alot n roll. Does this Happen with mower tires cause most I see r bias ply even the turf master or Carlisle smooth tires that I'm planning on
14
Driveline / Re: diff (doc)lock / extra spider gear?
« on: September 19, 2017, 08:48:21 pm »
I have a welder just not wantn to weld it.hate for a weld break while at wot. How many spider should I do ? One or two extra, and Wat do u mean when u say slop ?like there's still a lil one wheel action or something diff
15
Tires / bias ply mower tires/stock tires
« on: September 19, 2017, 04:35:27 am »
How do the stock mower tires(bias ply) handle at high speed do they roll or twist on turns like bias slicks? Does anyone use slicks and would the Carlisle smooth bias tires work for slicks?