Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Topics - chini

Pages: [1] 2
1
Briggs OHV & Vanguard / Piston clearance
« on: August 22, 2014, 07:47:40 pm »
  What kind of piston to wall clearance does an 49 inch need?
   Thanks, Kevin

2
Chassis / 3/4" Rotor?
« on: April 01, 2013, 11:47:16 pm »
  Where can I find a rotor for a 3/4" axle? Is Acme mowersports still open?
              Kevin

3
Coffee Shop / Commercial Rates
« on: March 15, 2013, 10:54:38 pm »
  I got a call from a Production co. They want to rent mowers for a commercial. Has anyone done this and if so how much did you charge/get paid. They offered to put me up in a hotel because of the distance. Any input would be great. He also wouldn't tell what the commercial was about.
             Kevin

4
Briggs OHV & Vanguard / Vanguard Throttle hook-up
« on: May 04, 2012, 10:00:54 am »
I just put 38" heads on a 35" vanguard. I am having trouble hooking up the throttle linkage on the 2bbl carb. If someone could post some pictures of what they did, it would be a big help.
              Kevin

5
Briggs OHV & Vanguard / 38" heads
« on: April 16, 2012, 01:43:26 pm »
When putting 38" heads on a 35" engine, which head gaskets do you use? And are there other things that I need?
                     Thanks, Kevin

6
Briggs OHV & Vanguard / ARC Flywheel
« on: April 13, 2012, 09:44:40 pm »
  I was trying to fire the boys mower when In realized there was no spark. So I changed the coil to no avail. Still no spark. I got a phone call, and while Talking I found the magnets in the ARC flywheel are bad. Any one else have this Problem? It ran the last race of the year OK.
  It kind of irritates me off that you pay for good parts that don't last. So now the circus begins to get new magnets and take it all back apart to fix it.
          Kevin

7
Briggs OHV & Vanguard / 44" overbore
« on: February 29, 2012, 05:53:30 pm »
How many of you are having problems with the head gaskets on thr 44" block bored to 49" + .020? Which head gaskets are in use?
                  Kevin

8
Briggs OHV & Vanguard / Starter Solenoid
« on: August 11, 2011, 12:42:04 am »
 Does anyone know the part # for the heavy duty briggs starter solenoid?

9
Briggs OHV & Vanguard / Intake Manifold
« on: June 28, 2011, 10:46:34 pm »
  I got some 38" vanguard heads to go on a 35" motor. Can somone give me the 2bbl intake manifold part # for a vertical shaft engine?
     Thanks, Kevin

10
Briggs OHV & Vanguard / 49" pistons
« on: April 20, 2011, 01:17:09 am »
Which is the best 49" inch Briggs piston to use? I want to start on the bad boy.

11
Chassis / Brake problem
« on: March 26, 2011, 10:07:32 pm »
I finally got to install and bleed the brakes on my new ride. They bled fine but don't get anywhere near the rotor. Complete MCP set up from EC. Is there a spring that pulls the pistons back? It says to adjust the pads, so I did. Now the pistons dont touch anything. They just go in and out. Is there some pad spacers to fix this? Theres .240" between the pads at rest. .125" thick rotor. What can I do to fix this?     Kevin

12
Briggs Flathead / Velocity stack
« on: February 21, 2011, 08:16:17 pm »
Does anyone make a velocity stack for the opposed twin yet?

13
Briggs OHV & Vanguard / Exhayst headers
« on: January 23, 2011, 06:30:45 pm »
Would someone post pics of your v-twin exhaust? I would really like an equal length set-up.  I need to build mine and would like some ideas. I'm running a mtd chassis and a 44 cuin intek.
              Thanks Kevin

14
Briggs OHV & Vanguard / STD bore?
« on: November 05, 2010, 07:55:23 pm »
Where can I find the spec's on the 49" Intek?

15
Briggs OHV & Vanguard / Top end kits?
« on: September 26, 2010, 04:51:00 pm »
Does anyone sell ready to go head/intake/carb kits. I'm just curios. Mostly for the vanguard twin, but all the overheads in general.

Pages: [1] 2