Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Topics - jacob

Pages: [1] 2
1
Briggs OHV & Vanguard / 22hp briggs vtwin
« on: March 06, 2015, 09:43:56 am »
Hey guys im not skilled to build a motor and i came across a 22hp briggs vtwin horizontal shaft and i want to build it to have alot of HP 50hp for say ? so my question is what parts should i start looking for to make this happen

2
Tires / Rims for my tires
« on: January 08, 2015, 10:42:35 am »
Hey guys new to this and im looking for some used or new rims for my 11-6.50-5 and 10-4.50-5 can someone tell me what to look at when buying rims for my size tires ?


not using these as race tires or anything just a project

3
Driveline / Tranny with reverse
« on: January 05, 2015, 10:59:59 pm »
Hey guys im building a racing mower from scratch and im looking for a budget tranny with reverse i can use with a horizontal engine

im new to this so bare in mind lol 3 speed or 6 is fine just as long i can get the mower/racer to go in reverse any help with what i need or a idea on how to mount/set it up would be great also

4
Chassis / help with spindles
« on: March 13, 2014, 10:37:58 pm »
hey guys im build a show/racing mower and my frame is made up of 1x2" box steel and i need help on how to figure out the front spindles camber and caster degrees ?

here is a vid on what it will kinda look like at the end https://www.youtube.com/watch?v=oDQOMuCks4g

but the frame is the same thing  but when making my own spindles how do i no what the camber and caster would be on them

5
Briggs OHV & Vanguard / engine re build
« on: March 05, 2014, 07:16:32 pm »
hey guys im just wondering how hard is it to switch out a Crank from a 18hp horizontal engine from a generator to a regular shaft ???

6
Briggs OHV & Vanguard / 18hp vtwin questions
« on: October 05, 2012, 02:27:54 pm »
Hey guys im new to all this and i just got a vtwin engine fir $250 and here is the info

Model number is 350447 type is 0119-014952 code is 93081811

Know it does not have a key switch or Harness and need help on how to bypass it to start it up

Can I jump it from the starter to crank over and do I need to hook anything else up ???

And another thing if I want little more than a mild rebuild how much would it cost to have done ??

7
Briggs OHV & Vanguard / vanguard NGK Spark Plug
« on: February 23, 2011, 11:18:18 am »
i have a 20hp horizontal vanguard performance engine and im wanting to replace the spark plugs in it but i have no idea what NGK Spark Plugs to get......... can anyone help me out please thanks....



8
Briggs OHV & Vanguard / vanguard shaft bolt
« on: February 19, 2011, 07:10:28 pm »
hey guys i have a vanguard vtwin engine horizontal shaft and i need a bolt that screws into my shaft would anyone no what size bolt it takes ? model number on the engine is 351447 thanks for the help

9
Briggs OHV & Vanguard / vanguard vtwin black smoke ??
« on: February 15, 2011, 04:04:54 pm »
hey guys i have a vanguard vtwin and i had cut off the muffler and inside the manifold was all black like dry powder but it was a light coat of it

should i be worried about something or is that normal

its a 20hp horizontal shaft vtwin and has a 2bbl carb  with some performance parts....is there a guide on how to adjust the carb on them ?

10
Briggs OHV & Vanguard / exhaust
« on: February 12, 2011, 01:48:42 pm »
where can i buy a exhaust for a 23hp vanguard vtwin ? or have one made

11
Briggs OHV & Vanguard / vanguard wiring
« on: February 09, 2011, 09:57:30 pm »
hey guys i have a 23hp vanguard vtwin horizontal shaft with mods to it and have a question

when i got the engine there where to wires for the 2 coils

well

im using a 5 pole switch to start the engine andto kill the engine.......i have everything hooked up but i have one BLACK KILL WIRE from my switch and i have 2 wires from the coils

so how do hook this up so my key switch will kill the engine ????

do i hook one coil wire to the BLACK wire going to my switch and the other to a GROUND on the engine/frame  OR?????

12
Briggs OHV & Vanguard / 12v batt will not crank vanguard v-twin
« on: January 08, 2011, 11:57:15 am »
hi guys i have a 16hp vanguard v-twin and i have a 12v car/truck battery thats getting over 12v and it will not start my engine, it cranks it a few times and thats it

would it be my battery or something on my engine ?

13
Briggs OHV & Vanguard / Bellcrank for a vanguard v-twin ???
« on: December 05, 2010, 03:28:45 pm »
hey guys just another ??? where can i buy a Bellcrank for a vanguard v-twin engine ?    im wanting to hook my throttle cable straight to the carb

14
Briggs OHV & Vanguard / v-twin kill switch help
« on: December 05, 2010, 10:07:12 am »
hey guys i have a 16hp vanguard v-twin and i just hooked up a new wiring harness on it and runs perfect, but when i turn the key to the OFF position it will not kill the engine ??? the coils wires are connected to the connector that is mounted on the side of the engine and my test light shows its getting ground

any tip on whats wrong ??

15
Briggs OHV & Vanguard / vanguard throttle help
« on: November 04, 2010, 11:20:55 pm »
hey guys i have a 16hp vanguard v-twin horizontal engine and i need some help on how do u guys hook up a throttle cable to the gov or carb PICS will help a ton

Pages: [1] 2
anything