Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Topics - gtpuller

Pages: [1] 2 3 4
1
Garden Tractor Pulling / CUB
« on: April 17, 2013, 11:37:47 pm »
This was the winter project. Well part of the winter!



Seems like I get them started but.....
Will see what happens.
Had a lot of welding practice on this one!

2
Coffee Shop / copper butt weld backer
« on: December 26, 2012, 07:21:40 pm »

3
Coffee Shop / weld through primer
« on: December 20, 2012, 08:48:59 pm »
Is 3M weldthrough primer really worth the extra money?

4
Coffee Shop / sprint cars
« on: October 14, 2012, 06:46:27 pm »
Excellent sprint car races last night! They had a couple of old school cars on display. Here is one of them.


5
Coffee Shop / cheaper?
« on: April 24, 2012, 09:29:54 pm »
Does any one know perhaps where I can get these cheaper?

http://www.etrailer.com/Enclosed-Trailer-Parts/Redline/L4080.html

6
Coffee Shop / space station
« on: August 14, 2011, 10:44:22 pm »
saw the space station a little earlier looked like a light bulb in the sky right where they said and right at the time they said pretty cool

http://spaceflight.nasa.gov/realdata/index.html

7
Chassis / minimum deck requirements
« on: August 13, 2011, 07:50:54 pm »
So I have this mower and the complete deck, and I have read the rules but i am unclear how wide that i should make the pieces that i am gonna cut for the deck. This will be a project in the future I just want to cut the pieces now so that I can recycle the rest of the deck. Along with the rest of my junk!!!!!

Thanks guys





8
Other Interesting Builds / building a hauler.
« on: June 12, 2011, 08:49:35 pm »
I've been working on a hauler started out as a 4x8 open trailer improving my welding skills as I go along. Unfortunately my other project on here is on the back burner. Anyway I need somewhere to store my tractor when it is finished.














9
Coffee Shop / engine test stand
« on: March 05, 2011, 09:28:47 am »
I am building an engine test stand. I am ready to have the hole cut in the engine mounting plate. Six inch diameter will work with the single. Will it also work with a v-twin?



10
Coffee Shop / snap rings
« on: February 26, 2011, 07:46:59 pm »
whats the proper cutter to use to cut snap ring slots  in a shaft

Thanks
Tim

11
Coffee Shop / rebuilding hard drive
« on: February 14, 2011, 06:39:00 pm »
do you install operating system or device drivers first

12
Coffee Shop / RAGB
« on: January 26, 2011, 06:44:10 pm »
Does the verticle shaft in the peerless 1000 RAGB come out from the top of the gear box? I don't want to take it apart yet, but I would like to know. The exploded diagram seems to show that would be the case but I am not sure.

Thanks

Tim Johnson

13
Coffee Shop / boring bar
« on: January 09, 2011, 12:30:20 am »
where is the best place to buy an adjustable boring bar for a mill? Need 1.100 inches. The ones that I have find are quite pricey, unfortunately thats probably going to be the case. Any setup tips from you machinists out there?

Thanks

Tim

14
Coffee Shop / ignition timing
« on: December 23, 2010, 10:10:33 pm »
Found this on the net sorry dont remember where

An engine at 6000 RPM has 100 Trigger pulses per second so the flywheel turns 360 degrees in 1/100th of a second so to change the timing one degree we will only have to delay the trigger pulse by 1/3600th of a second. Is this math right i think it should be 1/36000th of a second ie. (.027ms)/ degree of timing at 6000RPM.

Am I missing something?

15
Driveline / Peerless 2300
« on: December 16, 2010, 09:00:01 pm »
Brake shaft seal is leaking wasn't when first put back together anyway can the seal be changed successfully without tearing the transaxle apart?

Can get seals at
http://www.m-and-d.com/


Pages: [1] 2 3 4
anything