1
Briggs OHV & Vanguard / valve lift
« on: October 11, 2009, 12:19:31 pm »
What is the stock valve lift on the 28 single ohv?
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
2
Tires / alu rim and tire help
« on: July 01, 2009, 09:23:50 pm »
I just got a set of alu rims and turf master tires. I mounted them on the rims and put in the tubes, but after siting for a few hours one tube sprung a leak. I tried and tried but I can't get the tire off the bead to get the tube out. Any advice on breaking the bead? And yes I have the valve core out...
3
Driveline / 700 out put shaft
« on: June 07, 2009, 08:21:29 pm »
Do they make a P700 out put shaft that you can put the spocket on eather side of the tranny? If so, Does anyone have one they will sell me?
4
Chassis / Will this pass tech?
« on: May 11, 2009, 09:54:08 pm »
Will my back bumper pass ARMA tech?
5
Briggs Flathead / Witch one is lighter?
« on: April 28, 2009, 07:09:22 am »
Witch rod is lighter, the ARC billet rod or the stock OHV rod?
6
Driveline / crazy idea for ARC or EC
« on: April 14, 2009, 08:57:56 pm »
So we all know what the weak spot is on the pearless 700, the input shaft. Well when our engines started to break rods, what did we do? We had billet rods made.
So why not look into having a billet bottom case built?
So why not look into having a billet bottom case built?
7
Briggs Flathead / part #
« on: April 07, 2009, 05:58:56 pm »
What is the part #'s for a set of 28 flat head valve springs?
8
Briggs OHV & Vanguard / is it legal
« on: March 04, 2009, 11:05:44 pm »
Is it arma legal to have 2 air filters on a single engine?
9
Post your Pics! / My new toy
« on: February 10, 2009, 12:59:00 am »
Well I have me a new toy to play with on the track! This is a drag mower that will race at the drag strip at MOWDOWN MOWERSPORTS this year. This started life as a craftsman mower, but now has a Suzuki 125 4 stroke engine with a four wheeler rear end. The front has ben lowered and is direct steer. The trans is a 5 speed shift on the go. This thing is a beast!
10
Briggs Flathead / pto pans
« on: January 13, 2009, 10:16:36 pm »
Will the PTO pan off of a 14.5 OHV briggs fit the 12hp flat head?
11
Briggs Flathead / need some #'s
« on: January 02, 2009, 11:04:43 pm »
Can some one give me a briggs part # for a piston assembly for a 12hp?
12
Briggs Flathead / Need help
« on: November 08, 2008, 05:41:15 pm »
I need help on removing the valve spring retainer on mt flaty. I can't get the exhaust retainer to come off! I can get the intake off easy. I am using a spring compressor also.
13
Chassis / how to set up a chassi
« on: November 06, 2008, 08:18:20 pm »
How do you do the math on whare to cut the frame when using a transaxle?
14
Briggs Flathead / cam Q
« on: November 02, 2008, 11:25:41 pm »
I just got a new cam from precision cams. I was told I will HAVE to buy there lifters and springs to use it. Will it hurt my motor if I just run with the stock springs and lifters?
15
Post your Pics! / Experimenting with a craftsman
« on: October 12, 2008, 02:13:44 am »
Well I recently got a craftsman and I want to make a racer out of it as cheap as posible with out taking short cuts. I plan on using the stock transaxle and fliping it to make the mower lower. And to lower the front I plan on geting a peice of 1"x2" tubing and making a front axle. So here is the tare down! 
