Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Topics - carnett3

Pages: [1] 2
1
Coffee Shop / Tracks in Michigan and northern Ohio
« on: August 03, 2013, 01:30:17 am »
Im looking for a home track that is closer that the one I race at now. I live in Southeast Michigan and the drive to Potterville is about a hour and a half, so i want to try and find a track that is closer to me. Anyone know of any tracks in the like Adrian, Ypsilanti, Ann Arbor, Jackson area? Or even in northern ohio?

2
Chassis / new axle help
« on: June 21, 2013, 07:02:53 am »
I bought a component kit from ec but my issue is that I don't really know how it goes in ...

3
Driveline / peerless 700 problem.
« on: June 12, 2013, 11:18:10 pm »
I have a peerless and I have found that it is a nine spline axle. Now i have a dilemma 1 buy a new output shaft and maybe 4th or 5th gear set or, sell it and buy one with the correct spline. Let me know what you think I should do, right now my 5th gear is 3/1

4
Briggs OHV & Vanguard / Throttle Problems
« on: June 07, 2013, 12:34:08 am »
I have a hand throttle hooked up and it is awful, it needs work. when I have the clutch in it will rev some but it wont return and if I have the clutch out I will only rev a little bit. Whats my issue?

5
Chassis / Chassis Help!!!
« on: May 23, 2013, 01:21:26 pm »
I recently got my mower back together after lowering it and locking the axle and it turns once every couple weeks haha. Its turns awfully. I have 13x6.5-6s on the front and 18x9.5-8 on the back. I had clearance issues with my brake so I had to kick the tires way out so my brake would fit on. What do i need to do to make it turn better? I really dont wanna add weight to the front so I can turn so does anyone have any suggestions.
Thanks,
Colton

6
Driveline / Pulley Ratios
« on: May 09, 2013, 01:42:11 pm »
Okay for starters I have never raced, My build is almost done so i need to find a pulley ratio that will make me competitive. Im running a Spicer 4360 which is a 6:1 ratio and im running 16x7.5-8 on 8x8 rims. I have it built for g/p so I need to know what pulleys would help

7
Chassis / Deck halves
« on: May 09, 2013, 12:53:53 am »
How big to they actually need to be? like just there or a certain length?

8
Briggs OHV & Vanguard / G/P engine rules
« on: May 07, 2013, 02:09:08 am »
So for G/P rules is it legal to do mods such as using a offset key, milling the head, or retarding the cam a tooth?

9
Tires / where do i get 16x7.5-8s?
« on: May 05, 2013, 12:12:46 am »
I hear alot of people running them and My gp or cp needs rear tires, I plan on running a 8x8 rear rims. So where does one go about finding these?

10
Briggs OHV & Vanguard / 28 Flywheel question
« on: April 27, 2013, 03:01:05 am »
I have recently bout a 6611-28 flywheel for my 287707 and are they supposed to have 2 magnets? also tooth should I time the flywheel too?
Thanks in advance

11
Briggs OHV & Vanguard / ohv cam
« on: April 19, 2013, 04:05:54 am »
I thought I heard that I could find a cam for my 28 from some car motor, but I dont remember what car it was and how truthful that is?

12
Briggs OHV & Vanguard / model 28 wont start
« on: April 14, 2013, 06:39:09 pm »
So I was running then it stopped, I replaced the plug and magneto and messed with my solenoid and it ran for a while, then it stopped and it was dumping gas into the exhaust so I thought I had a valve sticking, pulled carb and intake off and it was literally full of gas, fixed the carb put the head back on and gaped the valves. Bought a new battery today and put it in and the solenoid was grinding so I think i need a new solenoid. but then I bypassed it and it cranked over but it wouldn't start. Can anyone help me get it running? Its bone stock

13
Briggs Flathead / Govenor issues
« on: April 11, 2013, 07:07:20 pm »
I recently bought a engine and the guy said it has no gov. what are the steps to making it work again. Motor is a 12 hp briggs 28

14
Briggs OHV & Vanguard / briggs 12 hp flatty vs briggs 14.5 ohv
« on: April 07, 2013, 11:02:16 am »
I have the ohv and the flathead. I was just wondering what would be more durable? What is going to be cheaper to fully build? The differences in power and tourque?

15
Driveline / 3/4 axle wheel hubs and brakes
« on: April 04, 2013, 03:05:53 pm »
I have found a bushing for my wheel hubs and I heard someone talking about a brake hat that will allow me to convert a 1 1/4 brake kit to fit on my 3/4 axle. Can anyone help me?

Pages: [1] 2