Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Smokingunz351

Pages: [1] 2 3 4
1
I guess no one has an answer for me.

2
so ive had this 16hp vanny for a while but just finally got around to installing it in the mower. Ran it today and noticed it sounded like it had a bit of a knock. im attaching a video of what it sounds like when its not running and i move the flywheel back and forth. Any help would be awesome.


3
Post your Pics! / GOLIATH
« on: September 18, 2006, 02:48:47 PM »
haha nice trick photography.

4
Kohler Engines / horzontal and vertical interchangability!!
« on: September 18, 2006, 02:43:41 PM »
SWEET!!! Thanx guys

5
Kohler Engines / horzontal and vertical interchangability!!
« on: September 14, 2006, 10:59:44 PM »
I have a friend who is willing to give me a vertical shaft kohler command v twin and i was wandering if all the parts for the horizontal shaft motors are interchangable with the vertical shaft engines. if so you could build a mean kohler if not then its no more than a boat anchor to me because it needs major head work to get it running again. any help would be greatly appreciated.



Bill
#99 F/X

6
Briggs OHV & Vanguard / Easy horse power
« on: September 14, 2006, 10:52:07 PM »
lol ive seen that video! its hilareous cause they cant kill it, it back fires through the carb like crazy but doesnt give up. kind of a :censored: poor setup they have but u can tell that motor is getting a good whif of the silly gas. why they put it on a push mower is beyond me. put it on sumthin you can ride.



Bill

#99 F/X

7
Post your Pics! / fx guys
« on: September 01, 2006, 10:45:49 AM »
heres mine

8
Briggs OHV & Vanguard / G-Force or Precision
« on: July 10, 2006, 11:48:48 AM »
im doing up a 14.5 briggs motor and just wanted some imput on which company does a better cam. ive ran a g-force cam from don before and have very good results with it, but im looking to see if theres one better out there. Does any body know the specs on the precision cam? Just let me know what you guys think.

Thanx,
Bill #99 F/X

9
Chassis / Brake fluid
« on: June 28, 2006, 10:03:21 PM »
thanx matt

10
Chassis / Brake fluid
« on: June 28, 2006, 09:16:18 PM »
Ive got an MCP go kart brake setup on my mower and cant figure out what type of fluid it uses. i think its uses DOT 3 but im not sure. any help would be great.


thanx
Bill #99 F/X

11
Briggs OHV & Vanguard / AVS piston rings
« on: May 29, 2006, 11:50:45 AM »
when you install the rings for the avs piston do you install them with the little dot so its facing the front of the motor or what? i have the book but cant find anywhere where is say how to install them. also if there in wrong what are some tell tale signs that there not in right with out tearing the engine down.

Thanx,
Bill #99 F/X

12
Driveline / red kevlar belts
« on: May 14, 2006, 08:38:13 PM »
does anybody know of a place on line where i can get  these belts? ive tryed the local mower shops and they wont give me the time of day unless i have a make and model of my mower. i tell them that its for a racing mower and they laugh at me. any help would be appreciated.

Thanx
Bill #99 FX

13
Driveline / tranny kicks outta gear
« on: May 14, 2006, 08:31:42 PM »
ive got a 700 series peerless and it cost me a race this weekend because it kicked out of gear causeing me to spin out. what would cause it to do this? it was just recently rebuilt with new shifter keys, cleaned out all the grease and added gear oil.

thanx
Bill #99 F/X

14
Driveline / 700 peerless help
« on: April 06, 2006, 08:07:21 PM »
ok i went and ordered the usual beef up parts for the 700 peerless(steel input and bevel gears and etc.) well today i went and pulled my tranny apart to put in the new parts but was soon stumped on how the steel bevel gear goes in. the bevel gear thats in the tranny has another gear on the side of it(im guessing this is 1st gear), but the new bevel gear doesnt have this and i have no idea on how to make this work with out it. any and all help will be appreciated.

thanx,
Bill

15
Chassis / lightening
« on: April 03, 2006, 08:17:21 PM »
yes, the lighter the mower the quicker it is. to make it light you strip off anything that doesnt make it faster or safer. It all depends on the chassis too. some mowers are just lighter than others. hope this helps


Bill

Pages: [1] 2 3 4
anything