Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Holey435

Pages: [1] 2
1
Briggs OHV & Vanguard / Re: Throttle setup for 21hp vtwin intek
« on: April 29, 2013, 10:56:55 pm »
I used a hood cable of a Venture van. I drilled a hole when the gonver stuff was hooked up and just ran one return spring.

2
Coffee Shop / Re: 5 hp class
« on: April 29, 2013, 10:51:37 pm »
They just mad u came up with the idea.

3
Briggs OHV & Vanguard / Re: Intek idle problem
« on: March 24, 2013, 08:43:06 pm »
Well just so u no i dont race with a group i race it is my back yard on my truck i have rods and flywheel coming but want to get it running right first. And when i bought the mower it had a single ohv and i want more power.

4
Briggs OHV & Vanguard / Re: Intek idle problem
« on: March 24, 2013, 08:32:16 pm »
Its all un hooked

5
Briggs OHV & Vanguard / Re: Intek idle problem
« on: March 24, 2013, 08:25:14 pm »
Factory motor other then heads.

6
Briggs OHV & Vanguard / Re: Intek idle problem
« on: March 24, 2013, 08:16:38 pm »
One if i touch the other one the motor still runs so i hooked it to the one that kills the motor.

7
Briggs OHV & Vanguard / Re: Intek idle problem
« on: March 24, 2013, 08:04:50 pm »
I have two wires they go in to a piece of shrink wrap and come out to wires it only kills the motor if i touch one wire.

8
Briggs OHV & Vanguard / Re: Intek idle problem
« on: March 24, 2013, 07:51:19 pm »
It is the kill switch is ground to the frame and i have to wires that go to coil and i turn my kill switch off aka tather and touch the blue and brown wire that go to coils and it only kills the motor touching the brown wire.

9
Briggs OHV & Vanguard / Re: Intek idle problem
« on: March 24, 2013, 06:22:33 pm »
Yea i used the harness on motor but only used one of both wires

10
Briggs OHV & Vanguard / Re: Intek idle problem
« on: March 24, 2013, 05:09:12 pm »
Ok i got it to idle good now. And rev with no load it shows 3800 on my dig. When im rideing it soon as i hit 2500 it starts braking up and popping. Any ideas 

11
Briggs OHV & Vanguard / Re: Intek idle problem
« on: March 24, 2013, 11:32:01 am »
When i ride it again i will try the choke. Thanks for ur imputs

12
Briggs OHV & Vanguard / Re: Intek idle problem
« on: March 24, 2013, 10:35:46 am »
It will idle down but it sounds like it it loading up on fuel.
Yea heads bolt right on.

13
Briggs OHV & Vanguard / Re: Intek idle problem
« on: March 24, 2013, 09:32:18 am »
Nothing only thing i did so far.

14
Briggs OHV & Vanguard / Intek idle problem
« on: March 23, 2013, 07:25:05 pm »
I have a 44 intek with 40 heads idleing  at 1500 it wants to stall. Then if im rideing the racer u get up around 3500 rpm it just falls on it face and starts brakeing up only on a load tho. Any help would be great.

15
Briggs OHV & Vanguard / Re: 44 intek wiring
« on: March 20, 2013, 11:55:06 am »
Can u send me a pic please and thank u

Pages: [1] 2
anything