1
Briggs OHV & Vanguard / Re: 40" pistons in a vanguard
« on: March 14, 2016, 01:41:21 pm »
Does the block have to be bored to run the 40 cube intek pistons?
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
2
Briggs Flathead / Re: walbro LMT 56
« on: September 18, 2015, 09:36:02 am »
Someone told me that Tecumseh makes one that will work. Part number 28945.
3
Briggs Flathead / Re: walbro LMT 56
« on: September 18, 2015, 06:55:05 am »
Hmmn. Where can you get it? I didn't see it on EC's site either.
4
Briggs Flathead / walbro LMT 56
« on: September 17, 2015, 06:02:25 pm »
Anyone have the part number or diagram for the needle and seat for these carbs and the adjustable needle for the bowl?
5
Briggs OHV & Vanguard / 2 barrel vanny carb jets
« on: September 10, 2014, 06:59:25 pm »
Does anyone know the part number for the 2 high side jets in the 2 barrel vanguard carb? I need the number for the jets out of a 28-20hp engine which are .038 because I need to bore them out to 40. I have a set of 23 carb jets but they are too large at .042.
6
Briggs OHV & Vanguard / Re: vanguard crank
« on: February 23, 2014, 10:39:17 pm »
Is their a visible difference? Neither of these cranks or in a block.
7
Briggs OHV & Vanguard / vanguard crank
« on: February 23, 2014, 10:01:52 pm »
Is their any difference in a 20 hp vanguard vtwin crank and a 14hp? I have two cranks so I'm trying to determine which cranks I have.
8
Briggs OHV & Vanguard / Re: 31 cu piston rings
« on: January 05, 2014, 12:04:19 pm »
standard bore. this engine is the one with the larger crank and uses the arc 6279 rod. I think it's the avs. I get them mixed up sometimes 
9
Briggs OHV & Vanguard / 31 cu piston rings
« on: January 04, 2014, 10:21:56 pm »
Anyone know the part number for the piston rings for a briggs 31 cu inch OHV?
10
Briggs OHV & Vanguard / Re: cam lift
« on: November 23, 2013, 07:13:52 pm »
anyone know the briggs part number for the briggs vanguard camshaft that is solid never ground and don't have the oiling holes? I know some people selling them but I just need the part number.
11
Briggs OHV & Vanguard / cam lift
« on: November 11, 2013, 05:55:05 pm »
What is the most lift you can put on a vanguard vtwin camshaft without running into some clearance issues? I know with the cheetah grind it is .308 lift and it will drop right in the block. Just curious. I'm thinking a .320 with small base circle will be about all.
12
Tecumseh Engines / torque specs
« on: October 18, 2013, 07:34:24 pm »
Does anyone know how many inch pounds the arc vtwin tecumseh rods torque to?
13
Tecumseh Engines / Re: tvt691 or ov691
« on: August 15, 2012, 07:07:25 am »Not off hand but George does and he has them available through EC (or used to).
Yeah I figured he would be the one to reply.
14
Tecumseh Engines / Re: tvt691 or ov691
« on: August 12, 2012, 09:01:01 pm »
Does anyone know the part number for the 17 hp carbs?
15
Briggs Flathead / parts numbers
« on: April 11, 2011, 08:06:35 pm »
Does anyone know the parts numbers of the crankcase/sump pan gasket, bottom oil seal, and exhaust gasket for a model 28 flathead?
Thanks
Thanks