Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - bchitwood

Pages: [1] 2 3 ... 5
1
Non-Affiliated Races / Creekside Speedway Grey Court SC
« on: July 09, 2018, 09:20:43 pm »
Hello  Just wanted to let everyone know that they have just opened a new track in Grey Court S.C. If you live close by show them some support .They are trying hard to get lawnmower racing started in this area . It's a nice track with great owners check them out on Facebook  Creekside Speedway if you don't have Facebook contact me and I will get you a number please share this with all the lawnmower racers you know . Thank you for your time

2
Briggs OHV & Vanguard / Re: 27 hp intek twin
« on: May 08, 2018, 09:08:04 am »
Thanks Tank the mower is about 4 years old ill have to look at the code  where are you racing at

3
Briggs OHV & Vanguard / 27 hp intek twin
« on: May 07, 2018, 09:34:56 pm »
I have a 27 hp intek twin on a JD zero turn grass cutter it back fired twice while cutting grass and broke a rod any ideas why. Thanks for any replies. It was full of oil

4
Briggs OHV & Vanguard / Re: 44 intek rich at idle
« on: April 18, 2018, 03:51:07 pm »
thank you

5
Briggs OHV & Vanguard / Re: 44 intek rich at idle
« on: March 01, 2018, 01:47:28 pm »
what size hole would i start with gonna give it a try thanks

6
Driveline / peerless gear box
« on: November 03, 2017, 01:06:41 pm »
has anyone bought a new ragb from EC i bought a 794111a and it doesnt have a seal on the bottom side it has a sealed bearing i called they said it is supposed to have a seal so they sent me another one and it also does not have a seal my question is does it need a seal with the sealed bearing it has gear oil in it and it is not leaking???? thank you

7
Driveline / Re: Gear box
« on: October 12, 2017, 04:35:07 pm »
Thanks

8
Driveline / Re: Gear box
« on: October 08, 2017, 09:34:53 am »
Thank you

9
Driveline / Re: Gear box
« on: October 07, 2017, 05:08:17 pm »
Thank you how do I tell if the one I got is a left I know it turns the wheels backwards lol can I tell my the numbers it has on it

10
Driveline / Gear box
« on: October 07, 2017, 03:36:48 pm »
If my drive is on the right side do I need a right angle box or a left angle box I bought what was supposed to be right angle box put it on and my wheels turn in reverse  ?

11
Briggs OHV & Vanguard / Re: 44 intek rich at idle
« on: August 28, 2017, 04:48:56 pm »
Thanks for the reply's i think i will leave it like it is thank you

12
Briggs OHV & Vanguard / 44 intek rich at idle
« on: August 24, 2017, 01:51:51 pm »
hello i have a 44 intek with a cheetah cam,dual valve springs, arc rods and flywheel ,heads cut 60 and ported and polished. it has a nikki two barrel carb with the low sides drilled to .030 with adjustable main jet.  it runs really good above idle but it runs real rich at idle. at idle for only 10 seconds it is blowing black smoke and engine starts to shut off. i can clear it out and it runs good  i was wondering if my timing could be off . i used the search but didnt help much. i can lean the high side down and it will clear up but then it wont accelerate it bogs when i give it fuel  any ideas .thank you   

13
Briggs OHV & Vanguard / Re: throttle linkage intek twin
« on: March 03, 2017, 08:46:36 am »
Thanks this helps a lot. what kind of carburetor are you running   

14
Briggs OHV & Vanguard / Re: throttle linkage intek twin
« on: March 02, 2017, 01:15:29 pm »
Thank you sir

15
Briggs OHV & Vanguard / Re: throttle linkage intek twin
« on: February 27, 2017, 03:57:17 pm »
ok thank you

Pages: [1] 2 3 ... 5
anything