Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Topics - crazycraftsman

Pages: 1 2 [3] 4 5 ... 9
31
Coffee Shop / Tac
« on: February 15, 2015, 11:10:06 am »
I was wondering if there's  a cheaper  3.5" tac that works right with the briggs motors? I have a jr. Dragster tac on one mowchine and looking for a cheaper one that (works) for my twin. Thanks for any info
Owen

32
Coffee Shop / Stroker motor
« on: January 24, 2015, 08:17:15 pm »
What's the difference over stock( how it works to what advantage ?)Thanks for any info

33
Coffee Shop / Any racing clubs left in Washington state?
« on: January 11, 2015, 08:48:35 pm »
Not sure if this is the right spot or not. Anyone Got a website or facebook page to any affiliated or local chapters of uslmra ,Arma or old school club? Looking to hit up some racing events down from B.C Canada. There's a few of us looking for a few road trips and meeting some new racers. Thanks for any help.
Owen

34
Driveline / Ec pulley hub for billet pulley.
« on: December 28, 2014, 08:59:46 pm »
Does it have a set screw in the hub or do you still have to use a shaft lock collar?

35
Coffee Shop / Balancing ohv single
« on: December 19, 2014, 08:38:01 pm »
Does anyone know someone that can do this right and guarantee it to be truly balanced. Someone that does this as a full time job. Thanks for any help. Someone that can balance twins and singles of all makes.
Owen

36
Coffee Shop / Cooper head gaskets
« on: October 24, 2014, 12:52:55 am »
Do I use a dressing for the gasket, high temp silicone , I've heard of sprays? What works and can still be removed with out distroying it when needed? Do I torq to factory spec ? Thanks for any input.
Owen

37
Chassis / Thickness of bmi front hub bearings ?
« on: October 16, 2014, 09:41:35 pm »
Making a bunch of spindle barrels and wondering if anyone could measure the thickness of the bearings in the cheap 3 bolt front hubs as I'm using the same ones in the barrel. 1-3/8 outside 5/8 inside by ? Thick-? Thanks for any info. Don't get all my parts till next week and got some time on a Lathe for free this weekend.
Owen
             :) PLEASE and THANK-YOU :)

38
Briggs OHV & Vanguard / Valve spring options
« on: October 15, 2014, 01:10:06 am »
Does anyone know we're to order a single performance valve spring kit. Looking for something not as agreesive as the duels ? Thanks for any info ( fully built 31 ohv)
Owen

39
Briggs OHV & Vanguard / 38 head on 30 cube vanny head gasket
« on: October 08, 2014, 11:38:08 pm »
Do I use a 38 cube head gasket, or 30 cube gasket or modify one of them to fit? Thanks for any info.
Owen

40
Briggs OHV & Vanguard / 30-35 vs 38 cube vanny valves
« on: October 02, 2014, 12:58:22 am »
Are they all the same size or are the 38 cube valves bigger and by how much? Do I get bigger valves put in my 30 heads or get 38 heads and put bigger valves in them to get mow hp and bolt them on. I've read on hear both ways??? Thanks for any advice:)
Owen

41
Tires / 6/5-6/7 fronts
« on: September 29, 2014, 09:39:10 pm »
Run on mostly ruff tracks, is a thinner tire in front better for bumps.

42
Coffee Shop / Quality and price on front hubs
« on: September 28, 2014, 12:08:22 pm »
Are the front hubs on Bmi and Ec the same or is the Ec hubs better? Cost is half as much from Bmi.
Owen

43
Coffee Shop / Who's got parts?
« on: September 26, 2014, 12:50:00 am »
Wondering who sells some good 5/8th by 5/8th spindles or 3/4 spindle by 5/8 inside bearing in barrel. 5/8th king pin. maybe weld your own kit or something . Looked bmi , hitch and EC .Thanks for any supplier .
Owen

44
Driveline / To the peerless 400 lovers out there
« on: August 17, 2014, 12:51:26 pm »
Have any of you lightened the gears inside these things. I run all three of my mowers with these and there awesome . Was thinking of drilling holes to lighten the gears 30% off. Less rotating mass. But was also thinking it might cause drag with the oil hitting and going through the holes in the gear. Anyone tryed this? Thoughts? Thanks
Owen

45
Briggs OHV & Vanguard / nikki two barrel carb problems
« on: July 22, 2014, 01:02:55 am »
My carb has a aluminum bowl with all lows and high side jets in bowl. Adjustable low needles on top,straight up coming down. Two 12mm plugs in bowl over mains. I need a carb kit and can't find part numbers. It's of a 35 cube vanny i was told. Ive looked up tons of repair manuals online and can't seem to find the right one. Need a needle , bowl gasket and float. Worth a try runnung like    . Any help would be great.Thanks
owen

Pages: 1 2 [3] 4 5 ... 9
anything