Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - greasemonkey92

Pages: [1] 2 3
1
Driveline / determine belt size
« on: June 22, 2014, 04:37:41 pm »
How do I determine belt size after my pulley swap? I have my old belt and can measure it and will measure my pulleys when I get a chance but wasnt sure if there was a simple way to determine without measuring the whole route... thanks for any and all help

2
Coffee Shop / Re: Races in Southwest Mo?
« on: June 22, 2014, 04:33:47 pm »
Yocum Creek Speedway is probably the closest place for you look embarrassed up online and in youtube

3
Driveline / lubricant for transaxle
« on: June 17, 2014, 06:33:47 am »
I tore down my first transaxle and going to weld it up today but I would like to know what should I put back in for a lubricant its going to be in a drag/play mower.... thanks for any and all input

4
Briggs Flathead / stock stroke on a 12.5 flatty
« on: June 07, 2014, 07:07:53 pm »
What is the stock bore and stroke on a 12.5 flatty I've looked several places and can't seem to find it... thanks for any and all help

5
Tires / 16x6.5-8 on 8x7 wheels
« on: November 20, 2013, 01:25:59 am »
Found a set of 16x6.5-8 tires and 8x7 wheels would I have any problems running this combo for a c/p for my first build?

6
Tires / Re: 8" x 8" steel wheels with 4x4 bolt pattern
« on: October 30, 2013, 09:16:31 am »
Bmikarts.com has some steel wheels 4x4 bolt pattern not sure wheel size

7
Driveline / 3/4 inch bore brakes
« on: October 29, 2013, 09:31:47 pm »
I am wondering where I can find brakes at that are 3/4" bore to fit my axles didn't see any on bmi and can't seem to find any anywhere else

8
Driveline / Re: how much to lower for flipped transaxle
« on: October 08, 2013, 04:30:41 am »
Thanks for the input give me a few ideas to work with...

9
Driveline / how much to lower for flipped transaxle
« on: October 07, 2013, 02:57:46 am »
 I am wondering how much I need to cut on my frame to make my pulley line up if I flip my transaxle?

10
Briggs Flathead / Re: oppy flathead
« on: October 03, 2013, 08:30:55 am »
Thanks was wondering if any others were out there also

11
Briggs Flathead / oppy flathead
« on: October 02, 2013, 11:55:43 pm »
I am wondering who or where the best place online is to get parts for an opposed flathead and what tricks or certain parts I may want to use are... its being put on a drag mower btw... thanks for any and all help

12
Garden Tractor Pulling / Re: front end
« on: September 29, 2013, 07:58:40 am »
The club I used to pull with had a few tractors with a tricycle front end and never had a problem with them its no different than a full size tractor pulling in a bigger class..  atleast in the last 15 years of pulling and watching pulls I havr never seen a tricycle tractor have a single issue... I guess it just boils down to opinion and comfort with the idea of it

13
Briggs OHV & Vanguard / Re: electric fuel pump help
« on: September 27, 2013, 11:39:52 pm »
As stated above its for a playtoy and also as slideways says more reliable

14
Briggs OHV & Vanguard / Re: electric fuel pump help
« on: September 24, 2013, 01:34:03 am »
Right now its more for a play toy being lowered and stretched and gravity fed tank won't work with the setup

15
Briggs OHV & Vanguard / electric fuel pump help
« on: September 22, 2013, 01:57:02 am »
If I  running a stock carb on a 14.5 ohv and put an electric fuel pump on what psi should I set the regulator at?

Pages: [1] 2 3
anything