Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - dicky43d

Pages: [1] 2 3 ... 12
1
Briggs OHV & Vanguard / Re: how to loosen bolts on billet flywheel
« on: April 01, 2015, 09:19:24 pm »
ok no luck yet. broke two allens. so now what? where can i get new bolts

2
Briggs OHV & Vanguard / how to loosen bolts on billet flywheel
« on: April 01, 2015, 04:27:33 pm »
i am trying to change gear on my billet flywheel but cant get bolts loose. are they right or left hand thread. and also any other ideas would help

3
Other Interesting Builds / my new project
« on: November 24, 2014, 08:18:17 pm »
My kids like driving my wifes racing mower and shes not racing anymore so why sell it, rework it.lol My son had a powerwheels car that didn't work so this is what im doing. LOL
 

4
Non-Affiliated Races / Re: 2014 ALL AMERICAN MOWER CHAMPIONSHIPS
« on: September 04, 2014, 01:41:45 pm »
we can still camp out in our trailers or pitch a tent at the track right.

5
Driveline / Re: setup wanted
« on: September 03, 2014, 06:57:28 pm »
with a 15 it will be 6.70 final ratio, with a 14 it will be 7.18 final ratio. This is all in 5th gear. my 3rd and 4th are the same

6
Driveline / Re: setup wanted
« on: August 27, 2014, 07:28:08 pm »
right now I am at 7.74 final ratio according to ec gearing calculator.

7
Driveline / Re: setup wanted
« on: August 08, 2014, 05:08:04 pm »
.

8
Driveline / setup wanted
« on: August 07, 2014, 01:38:05 am »
my home track the straightaways are 75 FT long tight corners. I have 7 on motor 5 on tranny for pulleys, 13 on tranny and 40 on axle for sprockets. I am pulling them out of the corner. Now my question is, I have been asked to run on a 1/4 mile track with 330 ft straightaways. What would be good to run for pulleys and sprockets? Also I am going to try and make it to the all American this year which I have been told are 175 ft straightaways. what would be good there. I am running a modified 31 ci briggs single cyl. please point me in the right direction. thanks again

9
Post your Pics! / Re: 2014 crazy racers modified
« on: May 18, 2014, 11:46:05 pm »
forgot the best part, we have to run a 1/8" thick steel shroud around the motor so I had my brother make one for me and hydrodip that too. lol

10
Post your Pics! / 2014 crazy racers modified
« on: May 18, 2014, 08:17:31 pm »
This is my 2014 crazy racers modified I race in Pukwana,sd. The hood and fenders my brother hydrodipped.



11
Coffee Shop / Re: raising money for local cause
« on: March 29, 2014, 12:51:45 am »
HERE IT IS



12
Tires / how good are these tires
« on: February 01, 2014, 05:56:49 pm »
http://www.overstockwheels.com/tires/tires-by-tread-pattern/greenspro-mowku-tires.html

Just wondering how good these tires would be on a dirt oval track, it will be on a modified at my local track which is probably equivalent to a mod-x I would say.

13
Coffee Shop / raising money for local cause
« on: January 30, 2014, 10:25:47 pm »
I have been racing mowers for 4 years now. Last year we started having a pink my ride night at our local track and the sponsor that night was relay for life. All the racers would paint there mowers pink, put pink tape on there mowers, or somehow have pink on there mowers for that nite. It was a success. This year we are doing it better. I got a mower ready for the stock class we have, and I will drive it. Then on Pink my ride night for relay for life, we are going to auction it off to the highest bidder, then money goes to relay for life. Hope it goes well and make it work to raise money.

Richard Dozark
Crazy Racers
Pukwana,SD
www.pukwanamowerracing.com

14
Post Your Video / Re: mod xr crash phatbottom speedway
« on: November 30, 2013, 09:08:11 pm »
That's one reason why I run metal hood n grille, easier to just bend back. Ya there heavier but I make it work

15
Non-Affiliated Races / battle at the barn
« on: November 27, 2013, 08:09:00 pm »
I come across this on face book. whos going? They are having outlaw mowers.
http://www.battleatthebarn.com/

Pages: [1] 2 3 ... 12