Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Topics - ARC C63

Pages: [1] 2
1
Briggs OHV & Vanguard / Bandolero's versus stock vanguard
« on: June 16, 2017, 08:23:05 pm »
I need some help I bought a Bandelero vanguard engine it's a 35 horizontal shaft when I pulled the heads off it's got flattop pistons not like the regular stock vanguards with the dish Pistons are these have different rod Lengths  than the stock do these require the stock of arc rods or do they require the longer arc rods like if you cut the dish off the Pistons

2
Briggs OHV & Vanguard / 49ic winter build
« on: October 20, 2015, 08:26:11 pm »
building up my engine its a stock at this point with .030 under heads with ec springs and retender

im looking for help with is the best parts form the best places to build a good 60plus hp engine with out braking the bank
 how big can I bore the cyls
is their a stoker kit for the crank
can I get longer rods with flat top pistons
what is the best cam the will not snap
and anything else any help would be better

3
Briggs OHV & Vanguard / vanny help!!!!!!!!!!
« on: September 29, 2014, 10:17:44 pm »
ok I have a 35cu vanny with
arc flywheel set at 2 1/2 marks off -
ec big bore that I have cleaned
ec cam
arc rods .100 over
.100 cut pistons
Dual valve springs
valve lash is .003 all four
new e3 plugs .023 gap
new coils at .040 gap
new diod wire
new fuel pump
new fuel filter

mower runs like crap pops and misfires will nice at times then will loss all power stalls out when racing then starts right back up

can any one help me?  im throwing money at it at this poiont :bash: :bash:

4
Briggs OHV & Vanguard / Fuel mix help
« on: August 01, 2013, 03:38:45 pm »
On my vanny with a ec carb my right size is lean and my left side is ok maybe a little rich but not bad mostly up in the rpm it has a skip like around 7000 Amy one come a crossed this be four

5
Briggs OHV & Vanguard / Inteck twin arc flywheel
« on: July 08, 2013, 07:09:39 pm »
My coils don't fit with the new flywheel and brackets the ground wire is hitting the brig

6
Briggs OHV & Vanguard / vany 35cub rpm
« on: June 15, 2013, 10:40:36 pm »
i have a 35 vany with flywheel .100 rods cut pistions cam and big bore plus head work
it is a new engine no race on it have let it run for 15min at a time once a day for a weak
i have a test and tune next weak end sould i limite the rpms or let it spin and how much is a self red line

7
USLMRA Races / NELMRA 2013 Schedule
« on: June 10, 2013, 07:45:09 am »
NEW ENGLAND LAWN MOWER RACING ASSOCIATION
2013 Schedule
 
 
This is where we Mow Through New England One Race at a Time
 
June 22nd Saturday Test & Tune Ledyard Fairgrounds, Ledyard CT. Registration and Tech starts at 10am / Racing starts at 12pm and will go to 3pm or 4pm, depending on the turn out.
 
 
<===THE REST OF THESE VENUE'S ARE OFFICIAL NELMRA POINTS RACES===>
 
August 3rd  Saturday, Cobleskill Fair, Cobleskill NY. Registration and Tech starts at 8am / Racing starts at 10am. This will be two points races back to back!!!! 
 
August 18th  Sunday, Washington County Fair, Richmond RI. Registration and Tech starts at 11am / Racing starts at 2pm.
 
 
August 23rd Friday night, Brooklyn Fair, Brooklyn CT. Registration and Tech starts at 4pm /  Racing starts at 6pm.
 
 
September 7th Saturday, Ledyard Fair, Ledyard CT. Registration and Tech starts at 3:30pm / Racing and Hot Laps will start at 6pm.
 
September 28th Saturday Durham Fair, Durham CT. Registration and Tech start at 9am / Racing starts at 12pm.
 
October 13th Sunday Portland Fair, Portland  CT. Registration and Tech. starts at 11am / Racing starts at 2pm.
 
October 19th  Saturday, Ledyard Fairgrounds, Ledyard CT. Registration and Tech starts at 10am / Racing starts at 12pm. This will be two points races back to back!!!!

8
Chassis / Weight help
« on: June 09, 2013, 08:35:10 pm »
Put the Bp on scales today forward

LF 106 RF 68 LR 58 RR 83 = 315
Wheel left
LF 136 RF 34 LR 0 RR 152 = 322

One is 7lbs diff ok or did something wrong

Two is this a good set up

And yes I'm not on it

9
Briggs OHV & Vanguard / pcv ????
« on: June 09, 2013, 05:58:15 pm »
On the the 28ci OHV can i block off the port and make a hole on the top of the valve cover to vent the engine

10
Briggs OHV & Vanguard / slow crank
« on: May 18, 2013, 09:28:56 am »
on my 35cb vangard with ec cam, arc rods, cut pistons dual spring valves

when i go to start the mower some time it spins nice other times spins over 1/2 a spin and stops 

11
Briggs OHV & Vanguard / EC BIG BORE two barrel carburetor
« on: May 13, 2013, 08:40:43 am »
how do i hook up the fuel lines any one have pics? it has 3 ports do i put a line on all 3 ?

12
Briggs OHV & Vanguard / Vanguard head gasket
« on: April 21, 2013, 03:05:13 pm »
i got the gasket kit form ec and it has two types of head gasket which one is better to run steel or graphoil?
I have long rods cut pistons and a ec cam 2

13
Briggs OHV & Vanguard / Motor bike wiring
« on: January 27, 2013, 06:10:54 pm »
In uslmra can u run like a racing bike ignition and or injection in a bp

14
Briggs OHV & Vanguard / stock rod?
« on: November 04, 2012, 07:13:48 pm »
ok next year im runnig a bp and just got a vany 18hp and plane on leaving the cam alone and port and polishing the had and puting ec springs on it and a worked card and intake so the thing is how many rpms will the the stock rod hold before they make a window in the block?

15
Chassis / us seat rules
« on: May 29, 2012, 10:19:34 pm »
i have been look of the rule on seat of PREPARED mower of the us
if i go off the arma rule will be legle

Pages: [1] 2
anything