Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - bodydropped72

Pages: [1] 2
1
Kohler Engines / Re: vtwin identification and carb help
« on: October 31, 2013, 08:43:04 pm »
Yes I'm aware of the tapered crank. I'm gonna use the armature from the generator side to make an adapter to fit
A polaris clutch.

2
Kohler Engines / Re: vtwin identification and carb help
« on: October 31, 2013, 07:26:57 pm »
What does the throttle linkage look like that I need and where can I get one. I'm not sure about the billet flywheel. That's on the pull start side I'm assuming

3
Kohler Engines / vtwin identification and carb help
« on: October 30, 2013, 11:41:02 pm »
I just got an 18-20 HP twin from a generator I'm gonna be putting in a golf cart. The carb does not have any air/fuel adjustment. I assume this is a preset to run at 3600rpm. What kind of carb do I need to look for to where I can run this through an rpm range instead of the 3600 it was setup to run at

4
Kohler Engines / Re: k321 carb
« on: August 25, 2008, 12:33:50 pm »
Im using the engine in my golf cart so id say its between service and racing mainly be using it to cruise around in

5
Kohler Engines / Re: k321 carb
« on: August 23, 2008, 01:18:32 am »
fuel is new right out of the can...think its a jetting problem?

6
Kohler Engines / Re: k321 carb
« on: August 22, 2008, 10:17:51 pm »
well i finally got it to idle still sounds like its missing in a way also the throttle response is kinda sluggish sounds like its gettin overloaded kept adjust the high idle(main) jet but it really didnt seem to help that much. ive only got about 1 1/2 to 2ft of exhaust on it not sure if this is effecting it let me know your thoughts..also i read a little bit on that weblink..think if i did that boring of the main needle and closed off the middle holes in the needle it will do anything...

7
Kohler Engines / Re: k321 carb
« on: August 22, 2008, 12:28:40 pm »
Thanks ill look it over later today

8
Kohler Engines / Re: k321 carb
« on: August 21, 2008, 06:37:24 pm »
All i know is that im gettin frustrated with it, it has compression fuel and spark i cant check the timing until i get it to run... not sure what else to do

9
Kohler Engines / Re: k321 carb
« on: August 21, 2008, 10:09:15 am »
they looked really good actually

10
Kohler Engines / Re: k321 carb
« on: August 20, 2008, 10:54:34 pm »
Well i got it to run a lil longer tonight had to have the throttle about 1/2 way open with main set at 3 1/4 and low set at 2 1/2 really thinkin its a carb issue when it was runnin it was popping pretty bad not sure what else to do

11
Kohler Engines / Re: k321 carb
« on: August 20, 2008, 09:13:22 pm »
well i did notice the other day my condenser was just hangin around noticed it would spark to ground when tryin to fire it so i found the clamp for it intalled it onto the block and no change as for tryin to install it mine is right net to the coil it does not go into the points cap like someone else was saying earlier

12
Kohler Engines / Re: k321 carb
« on: August 20, 2008, 03:41:49 pm »
Would any condenser work like one from a distributor? there all basically the same right?

13
Kohler Engines / Re: k321 carb
« on: August 20, 2008, 12:21:23 pm »
Ill check it but im almost positive it has not moved

14
Kohler Engines / Re: k321 carb
« on: August 20, 2008, 10:15:48 am »
thanks ill give that a try when i get home from work today. also gonna check my points gap.

15
Kohler Engines / Re: k321 carb
« on: August 20, 2008, 12:33:03 am »
lookin at the pics of your carb you have 2 holes in the choke plate and i looked at mine and it has none could making holes make any difference

Pages: [1] 2
anything