1
Briggs Flathead / walbro LMT 56
« on: September 17, 2015, 06:02:25 pm »
Anyone have the part number or diagram for the needle and seat for these carbs and the adjustable needle for the bowl?
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
2
Briggs OHV & Vanguard / 2 barrel vanny carb jets
« on: September 10, 2014, 06:59:25 pm »
Does anyone know the part number for the 2 high side jets in the 2 barrel vanguard carb? I need the number for the jets out of a 28-20hp engine which are .038 because I need to bore them out to 40. I have a set of 23 carb jets but they are too large at .042.
3
Briggs OHV & Vanguard / vanguard crank
« on: February 23, 2014, 10:01:52 pm »
Is their any difference in a 20 hp vanguard vtwin crank and a 14hp? I have two cranks so I'm trying to determine which cranks I have.
4
Briggs OHV & Vanguard / 31 cu piston rings
« on: January 04, 2014, 10:21:56 pm »
Anyone know the part number for the piston rings for a briggs 31 cu inch OHV?
5
Briggs OHV & Vanguard / cam lift
« on: November 11, 2013, 05:55:05 pm »
What is the most lift you can put on a vanguard vtwin camshaft without running into some clearance issues? I know with the cheetah grind it is .308 lift and it will drop right in the block. Just curious. I'm thinking a .320 with small base circle will be about all.
6
Tecumseh Engines / torque specs
« on: October 18, 2013, 07:34:24 pm »
Does anyone know how many inch pounds the arc vtwin tecumseh rods torque to?
7
Briggs Flathead / parts numbers
« on: April 11, 2011, 08:06:35 pm »
Does anyone know the parts numbers of the crankcase/sump pan gasket, bottom oil seal, and exhaust gasket for a model 28 flathead?
Thanks
Thanks
8
Briggs OHV & Vanguard / single OHV valve springs
« on: September 14, 2009, 07:57:46 pm »
I got a set of EC double springs and retainers here that was bought for a flatty. Will these springs and retainers work on a 14hp single OHV?
9
Briggs OHV & Vanguard / 20/23hp vanny bore and stroke
« on: January 24, 2009, 09:31:21 am »
Is the stroke the same on a 20hp and a 23? Best I remember the 23 just has a bigger bore, but the cranks are the same.
10
Briggs OHV & Vanguard / cam
« on: December 07, 2008, 08:03:49 pm »
What is the biggest cam you can put in a vanguard v-twin without griding or maching valve guides etc?
11
Briggs Flathead / 28/31 flathead
« on: May 28, 2008, 05:10:30 pm »
If you use the longer arc rod do you have to shave the piston if the block hasn't been decked?
12
Briggs OHV & Vanguard / 23 hp vanguard
« on: September 01, 2007, 12:27:11 pm »
Are the cams and rods the same in the 16-23 hp vanguard v-twins? I know the bore is different.
13
Tecumseh Engines / tecumseh single cylinder
« on: June 17, 2007, 06:07:45 pm »
Does anyone run tecumseh singles? I have access to a 16hp single. I'm assuming it's OHV. Have any idea where I could find specs on this engine?
14
Briggs Flathead / heads
« on: June 03, 2007, 05:36:17 pm »
How much difference are they in a stock 11hp head and a 12hp head? Which is more preferred to run.....11hp head or cut a 12hp head?
15
Briggs OHV & Vanguard / high torque starter for a 16hp vanguard v-twin
« on: March 21, 2007, 08:09:08 pm »
Ok if I read correctly the nippo starter from ARC won't work with the stock flywheel. So my question is are they a starter out there that will work with the stock flywheel and ringgear that has more power than the stock starter or as much power as the nippo starter from ARC?