Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Topics - PJG56

Pages: [1]
1
Want To Buy / Who Has It? / Briggs 49ci Intek vtwin
« on: October 29, 2022, 10:24:58 am »
Looking for alumnium intake off of a 49ci Briggs intek only,not the older ones from early 40&44ci Engines

2
Mower Engines & Parts / Intek vtwin EC Dominator Carb
« on: April 12, 2020, 06:38:50 pm »
I have a nice used EC Dominator carb for sale,carb was bought new in May 2019 only 4 races on it.
$ 165.00 shipped in the lower 48 states

3
Want To Buy / Who Has It? / Intek vtwin cam
« on: March 23, 2020, 11:28:38 am »
Looking for a Precision 355 cam,or something similar

4
Driveline / Ceramic 1.25" rear axle bearings
« on: January 09, 2017, 05:48:28 pm »
Just wondering how many have tried these and are they worth the extra cost..

5
Briggs OHV & Vanguard / Intek vtwin cams
« on: October 29, 2015, 01:22:50 am »
Just looking for some feed back of what different racers like for cams in the Intek vtwin

6
Briggs OHV & Vanguard / Intek vtwin EC billet cam specs
« on: May 10, 2015, 09:03:18 pm »
Anyone know cam specs of the new EC billet cam for the Intek vtwin?

7
Briggs Flathead / ISKY CAM OPPOSED TWIN
« on: July 04, 2014, 10:22:39 pm »
Everyone claims these are so good.
Why can't I sell mine?

8
Briggs Flathead / oppy cyl head temp
« on: June 23, 2014, 07:43:16 pm »
What should a good running moded oppy run for cyl.head temp?

9
Coffee Shop / Rim size for 13x6.5x6 turfmasters
« on: October 26, 2013, 09:19:53 am »
How wide a rim does any one run 9"?

10
Briggs Flathead / 3.57 bore head gaskets opposed twin
« on: May 16, 2013, 08:20:40 pm »
Anyone know the correct part numbers for these?

11
Briggs OHV & Vanguard / 44Intek piston
« on: August 17, 2012, 06:36:02 am »
Anyone know the cc volume of the dish in 44 Intek piston?

12
Briggs OHV & Vanguard / precision cams vtwin intek
« on: June 09, 2012, 07:02:42 pm »
anyone know duration,lift and valve lash for a Precision Cheatta Cam for an Intek VTWIN

13
Briggs Flathead / oppy arc 6624 flywheel
« on: January 22, 2012, 09:58:36 am »
Put new 6624 arc flywheel on 42 opp.will not run,set air gap multiple times from.010to.o44,and every where in between,still wont run,timing in stock position,magnet indexted to keyway same as stock wheel,changed mags with all new briggs parts known to be good,put stock flywheel back on set air gap .010 fires right up runs like a champ.Anyone got any ideas other than faulty magnet in new flywheel. THANKS PAUL

14
Coffee Shop / length of race tracks
« on: November 09, 2011, 06:26:31 am »
I,m in new hampshire would like to build a track or 2 behind my shop,I know there are probably many different sizes was wondering if someone could tell me of a couple of different lengths you run on,including corner radius. Thanks Paul

15
Briggs Flathead / oppy exhaust
« on: November 07, 2011, 03:14:24 am »
New to this forum,Ithink it's awsome,Now to my question,I,m building 42" oppy for ice racing wondering if i need the short stubs behind exhaust flanges that fit in exhaust ports.I read somwhere in here where it was a must on single cyl. flatties. thanks paul

Pages: [1]
anything