Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - grassthrasher

Pages: [1] 2 3 ... 16
1
Racing Mower Builds / Re: grassthrasher's 08 build
« on: February 16, 2008, 04:32:32 pm »
I finally got my WELDER !!! 570$ later, now i can start fabricating




for my clutch I'm gonna use a 5/16 grade 8 that should be strong enof


2
Racing Mower Builds / Re: my 2008 modefied tractor
« on: February 15, 2008, 05:45:56 pm »
for the font end it is welded to the sub frame

3
Racing Mower Builds / Re: Skeeter's Huffy F/X
« on: February 12, 2008, 08:07:26 pm »
this is what i did and it never came off




4
Racing Mower Builds / Re: Skeeter's Huffy F/X
« on: February 11, 2008, 10:44:04 am »
WOW this build is terning out rely good  :woo:

5
Driveline / Re: gearing chart
« on: February 10, 2008, 10:04:36 pm »
very nice, I will use that for when i'm gonna figerout my gearing

6
Chassis / Re: steering arms
« on: February 10, 2008, 08:38:30 pm »
it can depend on the rim, you might half to weld it on a angle so it dosn't hit the tire

7
Racing Mower Builds / Re: grassthrasher's 08 build
« on: February 07, 2008, 05:32:25 pm »
clutch pivot

8
Racing Mower Builds / Re: grassthrasher's 08 build
« on: February 07, 2008, 10:09:23 am »
Do you guys think that a 5/16 bolt will be strong enof for the clutchs ???  :confused:

9
Driveline / Re: tranny noise
« on: February 07, 2008, 08:50:23 am »
wen the brass bushings get hot don't they tern silver allmost like look like steel???

10
Racing Mower Builds / Re: grassthrasher's 08 build
« on: February 06, 2008, 10:24:03 pm »
last night I saw that its backwerds the arm should be on the auther side, I'm just gonna flip it over, I didn't drill the pivit point yet

the bolts are just siting theyre not bolted in yet I was just looking for sum diferent ideas on what to use, how meany, what size

thanks for the replys
Its starting to look better ?





11
Racing Mower Builds / Re: grassthrasher's 08 build
« on: February 05, 2008, 09:52:07 pm »
This is the starting of my clutch its made out of 1/4'' aluminum, wen I'm done if it doesn't tern out how I want I'm gonna redo it but with 1/2'' aluminum.





any advies on it?

12
Racing Mower Builds / Re: grassthrasher's 08 build
« on: February 04, 2008, 08:59:08 pm »
The tranny plate done.



Nice snug fit for the input shaft.


13
Racing Mower Builds / Re: grassthrasher's 08 build
« on: January 29, 2008, 08:51:59 pm »
well its 1/4'' i dont think it will flex much?

I put a few more bolts to holed it in


14
Racing Mower Builds / Re: grassthrasher's 08 build
« on: January 28, 2008, 09:43:39 pm »
Here is the starting of my tranny plate its made out of 1/4'' aluminum



the plate bolted

This is what I'm gonna use for my front end its 2''x1''x0.100''

15
Racing Mower Builds / Re: grassthrasher's 08 build
« on: January 27, 2008, 09:39:52 pm »
well they're is tips and nozzles I meant nozzles you haf to change the contact tips more often that is what holds the wire

Pages: [1] 2 3 ... 16
anything