Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - bimmerbaz

Pages: [1] 2 3 ... 11
1
Briggs OHV & Vanguard / Rings for a 31CI OHV briggs?
« on: December 13, 2023, 04:24:56 pm »
Hiya,

I am currently rebuilding a 31ci Briggs single . Its a Non AVS .I have measured the bore at 90.55mm which is within spec. I bought some standard rings and when checking the end gap I had .8mm gap  and it should be about .2mm.

I am looking for a part number or supplier to get oversize rings to reduce the ring gap . Or can i just run them with a bigger gap .

the part number I had for oversize rings is 960166 but I cant find any available.

Any help or suggestions would be appreciated

cheers Bazza  8)

2
Coffee Shop / Race timing equipment
« on: November 18, 2023, 07:50:24 pm »
Hiya,

We are looking at getting a transportable race/lap timing system for our mower racing events.

Looking for recomendations of what you guys are using.

cheer s

Barry 8)

3
Non-Affiliated Races / Racing Down under 1st race day highlights
« on: October 15, 2023, 08:15:38 pm »
Hiya,

Just thought you may be interested in our style of racing in New Zealand . This is a video of some of the days racing

https://youtu.be/tgEDkCqx6Kc?si=7WTff6FOtVW9IwMv

cheers

Baz 8)

4
Briggs OHV & Vanguard / Re: Briggs Single engine rebuild
« on: August 20, 2023, 06:54:24 pm »
Hiya,

Part 5 up Now

https://youtu.be/fUo8i3gZdEk

cheers

Baz  8)

5
Briggs OHV & Vanguard / Re: Briggs Single engine rebuild
« on: June 18, 2023, 06:39:45 pm »

6
Coffee Shop / Mower Racing Down under
« on: May 02, 2023, 04:38:18 pm »
Hiya,

just thought i would share this video of some mower racing in New Zealand. Held in Morrinsville and hosted by the Bay Waikato Mower racing club.

https://youtu.be/OM4T5ImjVsg

Cheers Baz 8)

7
Briggs OHV & Vanguard / Re: Briggs Single engine rebuild
« on: April 30, 2023, 10:07:01 pm »
Part 3 up now

https://youtu.be/bH7rlEmcbCY

cheers Baz 8)

8
Briggs OHV & Vanguard / Re: Briggs Single engine rebuild
« on: April 25, 2023, 06:27:54 pm »
Hiya,

this part 2 of the engine rebuild . thought it might be helpful for some

https://youtu.be/2OF0xJVcwhU

Cheers  8)

9
Briggs Flathead / Re: No spark from Alloy flywheel
« on: December 08, 2022, 03:05:39 pm »
Righto,

thanks to those who messaged , i have fixed the problem. when i removed the magnet from the old flywheel it was not attached to the plastic case or the steel rounded piece. I must have put it back the wrong way and the polarity was wrong. I changed the polarity of the magnet by turning it around and now i have spark.
good bit of learning about the basics of magnetism.

cheer s

 8)

10
Briggs Flathead / No spark from Alloy flywheel
« on: December 06, 2022, 03:51:27 pm »
Hiya,

I am currently building a 28ci flat head and wanted to put an allow flywheel on it. I got one from a friend that is not an ARC or commercially made  flywheel. I swapped the magnet from the original flywheel onto this alloy flywheel and now i have no spark from the original coil. So i put the original flywheel and magnet back on and i have spark again.  Any suggestions as to why when i swap the flywheel i loose spark?.

cheers

 :bash:

11
Briggs OHV & Vanguard / Re: Briggs single Carb secrets
« on: October 10, 2022, 04:05:10 pm »
thanks for that .

cheers  8)

12
Briggs OHV & Vanguard / Briggs Single engine rebuild
« on: October 10, 2022, 04:04:06 pm »
Hiya,

I thought this might be of interest to some of you guys. I am  doing  refresh for racing on this 31ci motor .

https://youtu.be/3V4O30r_zn8

Cheers  8)

13
Racing Mower Builds / Re: Bazzas Backyard Budget Builds for Billy-Bob
« on: July 25, 2021, 09:15:29 pm »
part 13 last one

https://youtu.be/efp7QgYxdt0

cheers  8)

14
Racing Mower Builds / Re: Bazzas Backyard Budget Builds for Billy-Bob
« on: July 12, 2021, 10:36:59 pm »
part 12 good to go

https://youtu.be/rny-_8Ew2IE

cheers Barry 8)

15
Racing Mower Builds / Re: Bazzas Backyard Budget Builds for Billy-Bob
« on: June 08, 2021, 10:59:41 pm »
Part 11 up now.

https://youtu.be/vJy74fvrWuc

Cheers Barry  8)

Pages: [1] 2 3 ... 11