Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Tony Loveless

Pages: [1] 2 3 ... 41
1
Driveline / Re: Billet pulley
« on: March 13, 2015, 10:57:21 am »
More than likely that's what it is.  Your clutch looked fine the last time I looked at it.

2
Driveline / Re: Billet pulley
« on: March 11, 2015, 01:54:05 pm »
Logan I don't know how long you have ran the belt but I have had that happen to me until the belt wears in.

3
Coffee Shop / Re: Getting back in the game!
« on: January 22, 2015, 04:15:33 pm »
Yea.  I quit when we had our son.  Also have a little girl now and my son is getting older so I figured its time to introduce him to the sport.  Planning on building him a small mower with like a 3.5 hp motor in a year or two.

4
Coffee Shop / Getting back in the game!
« on: January 22, 2015, 11:27:56 am »
Just wanted to stop in and say that I'm back.  Have a lot of friends I have raced with in the past and haven't seen or talked to any of them since I quit.  Hoping to be back on the track at the start of the season.  :twothumbsup:

5
Coffee Shop / Re: ????
« on: February 14, 2014, 02:33:43 pm »

6
Coffee Shop / Re: ????
« on: February 14, 2014, 11:30:09 am »
Y'all have all lost it lol

7
Coffee Shop / Re: Hegar front brakes on EC spindles
« on: February 14, 2014, 11:27:30 am »
Yup :thumbsup:

8
Coffee Shop / Re: Hegar front brakes on EC spindles
« on: February 14, 2014, 12:05:56 am »
No my cousin runs them with no clearance issues at all.  I have Douglas 7.25 and had to do some slight mods to get them to work.

9
Coffee Shop / Re: Hegar front brakes on EC spindles
« on: February 13, 2014, 06:18:41 am »
Van K 2.5" will clear also

10
Chassis / Re: B/P brakes
« on: December 09, 2013, 03:21:49 pm »
The MCP won't fit on an Ec axle though will they?

11
Coffee Shop / Re: Prayers for fellow racer!
« on: September 27, 2013, 11:25:21 pm »
Doctors say everything is looking good.  May possibly get to come home tomorrow.  I know he is ready after 7 days.

12
Coffee Shop / Prayers for fellow racer!
« on: September 27, 2013, 12:06:37 am »
I got this on here later than I wanted but I'm asking for prayers for a fellow racer.  His name is Jason Murray ( I believe Murrdawg on here).  He is the president of the ARLMRA and crashed in Batesville, Ar this past Saturday.  He suffered a broken hip and pelvis.  They had to take him to Little Rock where they done surgery yesterday placing rods in.  He is now doing some physical therapy.  Jason has ran several national races this year so I'm sure a lot of you have met him.  I'm afraid this injury will put a stop to his racing career though.  So I'm asking you say a prayer forbhim and his family as he gets through this.  Thank you.

13
Briggs OHV & Vanguard / Re: A little Inktek help please
« on: September 03, 2013, 08:28:18 pm »
Just went through this.   Ditch the pan gasket for sure.  I used motoseal and center valve covers.  Took care of the problem

14
Briggs OHV & Vanguard / Re: Build 30 cube vanny or 40 cube intek.
« on: August 20, 2013, 05:35:04 pm »
Lol yep jim before ya know ill be the "Intek Outlaw"  :lol:
Me too!!!

15
Briggs OHV & Vanguard / Re: 35ci vangaurd with 40ci Intek pistons
« on: August 19, 2013, 10:58:29 am »
Nope they will explode lol.  Cheetah cam by precision is a good cam

Pages: [1] 2 3 ... 41