1
Coffee Shop / Tach
« on: August 13, 2015, 01:38:32 pm »
I was woundering if a trail tech tach will work on my 18 hp intek. I was looking at the vapor
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
2
Briggs OHV & Vanguard / 18.5 intek rebuild kit
« on: August 09, 2015, 10:05:53 pm »
We're can I find a rebuild kit at for a 18.5 intek. Just want to freshen it up before I put it in my mower
3
Briggs Flathead / Sealing a two piece oppy intake
« on: August 04, 2015, 01:05:24 pm »
I called ever mower shop around me looking for a gasket they said they can't get them .can I just use gasket sealer on it .like some high temp sealer.or is there another my
4
Chassis / Day dreaming
« on: July 20, 2015, 01:57:12 pm »
Later on I plan on to build a fxs .how wide should they be 40 or 42 . I'm not going to have any offset in it. Just trying to get a plan together
5
Coffee Shop / Exaust question
« on: July 17, 2015, 12:39:36 pm »
What degrees do I need to cut to make square exaust. I love they way they sound .
7
Driveline / Spider gears
« on: July 09, 2015, 11:21:40 am »
Can someone please tell me were to buy spider gears at for a 820 peerless. I have Google it and can find anything
8
Tires / Let me try this again
« on: July 07, 2015, 12:23:11 pm »
I was woundering what size rims they run on the fxs mower. I no there is a bunch of sizes that people run .just trying to get a plan together
9
Tires / Day dreaming
« on: July 04, 2015, 12:11:24 pm »
I was wondering what a budget fxs tire and rim set up would be . I was thinking about a 6x8 1/2 rim of the rear and a 6x7 in front with a 13x6.50 x6 turf master tire.or something like that all the way around.would this work
10
Post your Pics! / Looking for pictures
« on: July 03, 2015, 06:32:32 pm »
I'm looking for pictures of a fxs or fxt murray wide body. If someone could please post up some I would really appreciate it
12
Briggs Flathead / Intake and after market air filter for oppy
« on: June 14, 2015, 02:46:07 pm »
Ok I have a two piece aluminum intake. Would it be better then my cast iron intake the two piece looks like it has bigger runners. My oppy will be going on a super stock mower next question. I seen a filter set up on here that have a big square filter said it was what he used on his intek it was a k&n filter . Im looking for a way to run a aftermarket air filter with out drilling my carb to vent it. any pics or help with this will be greatly appreciated
13
Driveline / Clutch mounting
« on: June 12, 2015, 01:24:31 pm »
We're should my clutch be mounted. closer to my jackshaft or mid way between my jackshaft and drive pulley . This is for my super stock
14
Chassis / Tap and bit size
« on: June 11, 2015, 01:26:46 pm »
I'm going to make my own steering rod that goes to from my steering shaft to the front axle.and some rod s for my master cylinder. I ordered 9/16 0.328 aluminum tubing from mcmaster carr . Do I have to drill and this tubing or can I just tap it . And if I do have to drill it what size bit do I need and does someone have a part number for a mcmaster carr tap that I need. I no that I have to get a right and left handed tap
15
Coffee Shop / Not for sure
« on: June 10, 2015, 01:23:16 pm »
I'm not for sure were to post this at. But can I use a clutch master cylinder off a car and use it as a brake master cylinder on my mower