Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Rocket Ron

Pages: [1] 2 3 ... 12
1
Driveline / Re: 700 Peerless output shaft chewed through houseing
« on: December 17, 2015, 10:20:39 pm »
Kiwi, Better idea yet, Let me machine a set of E.C.  trans cases Lots better cases than perless as of the alloy their made of. Only one way freight. Will cut cost in half in freight alone. Trans case, labor for work,freight. won't break the bank. Just a thought. Ron.

2
Driveline / Re: 700 Peerless output shaft chewed through houseing
« on: December 17, 2015, 06:06:20 pm »
I sell and ship parts to newzeland,and austraila all the time usps frt.may be less coastly than you may think as though trans case's aren't cheep. not to mention failed parts during race weekend either... Just some food for thought!!!!  Ron.




3
Driveline / Re: 700 Peerless output shaft chewed through houseing
« on: December 14, 2015, 11:48:40 pm »
with problems like that happening over and over you should send your case haves to me to be line bored and have roller bearing installed then that problem will be cured.  Ron.

4
Briggs OHV & Vanguard / Re: 31-33 Avs factory pistons
« on: November 26, 2015, 07:32:40 pm »
Well I guess thats why some people spend all thair time on the comp. Insted of in the engine room or on the Dyno. That question is always ansered at the track and not on the keyboard!!! Ron.

5
Briggs OHV & Vanguard / Re: 31-33 Avs factory pistons
« on: November 25, 2015, 09:11:36 pm »
cSorry for the confusion on the matter the only eng. I 've ever built with gov. in it went back on a grass cutter  . and the cast pistons in them held up very well at 3600 rpm . wish you luck at 5 grand plus at5 grand plus.

6
Briggs OHV & Vanguard / Re: 31-33 Avs factory pistons
« on: November 25, 2015, 06:05:48 pm »
Thank's Jeff but I sure that one would have been way over thair head's. So I did'nt even try to explain. Ron.

7
Briggs OHV & Vanguard / Re: 31-33 Avs factory pistons
« on: November 24, 2015, 06:36:51 pm »
Dah.. If you only understood rod ratio!!!  Ron.

8
Briggs OHV & Vanguard / Re: 31-33 Avs factory pistons
« on: November 23, 2015, 03:49:28 pm »
They are not .590-.620 comp. height

9
Briggs OHV & Vanguard / Re: 31-33 Avs factory pistons
« on: November 21, 2015, 08:18:18 pm »
Yes. They are in the same place. But unforturely they are in the wrong position.

10
Briggs OHV & Vanguard / Re: 33ci flat top piston?
« on: November 19, 2015, 07:24:33 pm »
Tom, I still hav'nt gotten that phone call yet. Just recived a fresh batch of rod's this week I think one even had your name on it .. Ha Ha Can't go wrong .  Ron.

11
Driveline / Re: 700 peerless wont shift
« on: November 16, 2015, 06:16:52 pm »
Don't tear it down send it to me if you want a bullet proof trans people run them all season with no problems at all.   Ron 843-287 2042

12
Briggs OHV & Vanguard / Re: 33ci flat top piston?
« on: November 16, 2015, 06:11:00 pm »
Tom,If you have a phone with tap a talk I know it will dial my number. It surley will be  worth the call!!!! 843-287 2042.

13
Briggs OHV & Vanguard / Re: 33ci flat top piston?
« on: November 13, 2015, 07:58:33 pm »
No web site, Just a phone call away. 843-287 2042 Ron.

14
Briggs OHV & Vanguard / Re: 33ci flat top piston?
« on: November 11, 2015, 01:53:02 pm »
Yes Tom I sell JE piston works with my .490 conn. rod.    Ron.

15
Briggs OHV & Vanguard / Re: 49ic winter build
« on: October 20, 2015, 10:07:35 pm »
 Long rods, Flat top JE pistons,Bilitt cam core I keep in stock, as many other hi performance parts you  will need to make good power and be reliable. Hope I can be of some help to you.  Ron.
  Yes, I have true needle bearing rocker arms as well I keep good vavle springs and 7075 solid push rods also  Ron, 843-287-2042 any time cell phone # 50 Hp is capable!!

Pages: [1] 2 3 ... 12