Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Topics - pjhusske

Pages: [1] 2
1
Other Engines / Kaw motor info
« on: September 10, 2013, 11:34:59 am »
Is there any other way to find out what motor I have?  Plastics on the motor is missing.. Its a Kaw twin something...
Let me know with any feedback

2
Tecumseh Engines / 8HP motor
« on: June 06, 2011, 10:16:19 pm »
Tecumseh 8 hp Engine Vertical Shaft
Model TVM220-157306L

Is this a good motor to build for a mini/ap???

3
Chassis / is this ok?
« on: February 01, 2011, 04:42:07 am »
Can I cut out piece of frame so my steering link from tire to the other tire will clear so I can get the frame lowered to 4 inchs?

4
Briggs OHV & Vanguard / 28 AVS piston.
« on: March 03, 2010, 12:51:46 pm »
Is this piston a short skirt like the 31's are?????  The piston in a 28 model AVS

5
Tecumseh Engines / is this a tec. number
« on: November 27, 2009, 04:05:06 pm »
Is this a tec. Number?
VM80-150092D-Ser-7144D. 8hp something anyone help me out? Thanks

6
Racing Mower Builds / PJs new winter project.
« on: November 18, 2009, 05:14:00 pm »



Just dont what class to run it in....

7
Other Engines / Single Kaw.
« on: October 28, 2009, 11:49:36 am »
How do theses motors run?
Any perf. parts for them?

8
Chassis / Bouncing
« on: August 30, 2009, 09:07:42 pm »
I have notice that I have been bouncing more than you would think coming out of the corners.  Even with low tire pressure.
Anyone have suggestions on why this is??

9
Briggs OHV & Vanguard / Lash Caps Single OHV
« on: August 13, 2009, 05:01:07 pm »
The lash cap keeps falling out on my single. Any ideas on keeping them in?  Running roller rockers I think that they have egg shaped. 
May have to go to some mod. stock rockers. Let me know of any feedback
Thanks

10
Briggs Flathead / Clean up a block
« on: April 12, 2009, 08:52:25 pm »
What is the best way to clean surface rust off? In the cyl. and valve area..

11
Briggs OHV & Vanguard / 31 OHV Head gasket
« on: April 07, 2009, 11:02:24 am »
Any one know the part number for a 31 OHV head gasket right off hand?????
Thanks

12
Post your Pics! / My New Chass..
« on: March 09, 2009, 09:15:08 pm »


My new chass. for the 09 year so far. Just about done

13
Tires / Mounting
« on: March 08, 2009, 02:29:38 pm »
Man mounting a 13x650x6 on a 8 1/4 rim is a pain in the but.
Any suggestions went through two tubes.....

14
Briggs Flathead / Flathead Port and Polish
« on: November 12, 2008, 08:23:21 am »
Lets see some good pic. of a good port and polish job on a 12hp or whatever flathead.
Lets see what you got

15
USLMRA Races / US and the Shelby,NC Race
« on: July 19, 2008, 08:57:58 pm »
Anyone know what had happen with this event?
Why?????

Pages: [1] 2