Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Topics - snaponmower729

Pages: [1]
1
Briggs OHV & Vanguard / Horizontal Vanguard v-twin
« on: September 21, 2009, 09:25:30 pm »
I have a 16hp vanguard v-twin and I am courious what it would take to mount the motor in a vertical orientation. I am aware that I will need to change the carb but I need to know what is different internally if anything. Thanks

2
Kohler Engines / Kholer cammand 14hp
« on: December 07, 2007, 12:00:16 am »
I am rebuilding my kholer cammand 14hp ohv and i was wondering if it would be a good idea to take the the balance counter wieght out of the engine or would this be detremental to the performance of the engine?

3
Tecumseh Engines / 17.5 enduro
« on: November 05, 2007, 12:38:17 am »
I have 17.5 hp enduro and when I tore the motor down it has two jackshafts in it. They have wieghts on them and my question is can I remove these to free up some spinning mass, and if I do would I have to get my crank balaned?

4
Tecumseh Engines / What carb?
« on: November 03, 2007, 10:33:36 pm »
What size of tillotson carb should I use on my 17.5 hp motor to make it pull through the whole rpm range because I race on a road course style track and I am constantly slowing down and speeding up.

5
Tecumseh Engines / 17.5hp Enduro cam
« on: October 16, 2007, 12:26:39 am »
Does anyone know if there is a cam out there for a 17.5hp Enduro single cylinder engine out there and if there is could you please post a link the web site where I can get it. Thank You much

6
Tecumseh Engines / What tach and oil pressure gauge do i use
« on: September 18, 2007, 12:24:41 am »
I have a Enduro 17.5hp single cylinder engine and I would like to know what kind of tach and oil pressure gauge I should use.

7
Tecumseh Engines / Enduro 17.5
« on: September 04, 2007, 12:36:36 am »
Does any one know how many cubic inches the the enduro 17.5 hp engine is?

8
Driveline / Does anyone perpare a Peerless 600 transaxle
« on: August 30, 2007, 10:32:55 pm »
Does anyone prepare a Peerless 600 transaxle other than putting a solid axle trough it?

9
Driveline / Peerless 930
« on: August 20, 2007, 12:27:50 am »
I have a peerless 930 series transaxle and I plan on putting it behind a 14 ohv briggs and I was wondering if this transaxle would hold up?

10
Briggs Flathead / Is there any 14 hp opposed twins
« on: August 04, 2007, 12:46:09 am »
Are there any 14 hp opposed twins that have a pressurized oiling system?

11
Kohler Engines / Kohler 14hp Cammand Cam
« on: August 03, 2007, 12:24:06 am »
Does anyone know where I can get a cam to liven up my 14hp kohler Cammand engine? I would really apriciate the Help thank you.

12
Driveline / Did I get a good deal?
« on: July 26, 2007, 12:40:23 am »
I recently purchased 14 mowers from an old small engines repair shop for $140 bucks $10 bucks a mower. They are all old craftsmans that are pretty small but they all have. Peerless 400 series transmissions in them. I have taken all of the transmissions out and cleaned them and all of them are the same 401A or 400 model numbers. I just want to know if I bought something that was a good investment.

13
Driveline / Peerless 400 parts diagram
« on: July 16, 2007, 09:32:21 pm »
Does anyone know where I can find a parts diagram for a Peerless 400 transmission on the web that has parts numbers listed on it.
Thank You for your help if you can.

Pages: [1]
anything