Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - leadslead

Pages: [1] 2 3 ... 92
1
Coffee Shop / Re: Any one now about wood splitters
« on: July 31, 2015, 08:52:10 pm »
Thanks for input

2
Coffee Shop / Re: Any one now about wood splitters
« on: July 31, 2015, 07:48:25 am »
So the faster it isthe less power it has for hairy hickory or knots ? Also the one that hooks to 3 point is that faster than 20 sec cycle time

3
Coffee Shop / Any one now about wood splitters
« on: July 30, 2015, 09:16:58 pm »
I have a 27 ton blue box store specHal it's cycle time is around 20 sec I was woundering what I could do to make it faster I split 30-40 cord a year I'd like to split more but splitter is slow & I run out of time any advice would help thanks buying new spitter is not a option

4
Chassis / Re: 90's Murray build
« on: February 14, 2015, 07:34:38 am »
One inch angle iron down both sides stitched in x members where motor. Sits ...I use 1/8-1/4 2in stick that way motor sits flat on solid plat form

5
Briggs OHV & Vanguard / Re: Briggs 31 Single Non-AVS OHV Upgrade Path
« on: January 29, 2015, 04:34:00 pm »
Valve springs send cam to isky balenced crank

6
Coffee Shop / Re: Who would build it?
« on: January 24, 2015, 06:46:32 pm »
Longs it's. Safe run what yer brung if yea lap every one in heat start in the back for featcher ... Just my thought  ...... Some of the $$ u can dump in to a single or twin is crazy but when u grab a hand full $$ well spent .

7
Coffee Shop / Re: Billet Flywheel Required for Intek V-Twin?
« on: January 16, 2015, 07:31:36 pm »
A wize man once said if u can not afford a doller a day tords racing then don't race 364-365 days a year doller a day = flywheel this day next year at your door

8
Coffee Shop / Re: Right angle gear box
« on: January 02, 2015, 08:50:21 pm »
They work good better than 700 by a land slide some where designed for mower decks on older mowers so to take that kinda beating ... Plus Thier pritty much foul proof ... Not as many moving parts

9
Tires / Re: Intek
« on: August 05, 2014, 07:40:22 am »
15 hampsters & a snake that will make them move ... Isky cam ... Rocket Ron's rollers steel push rods billet rod dual springs big valved heads ec air adapter .. Arc fly wheel

10
Driveline / Re: Gear ratio?
« on: July 28, 2014, 09:21:06 pm »
What's streight away  how wide are corners

11
Driveline / Re: centrifugal clutch recomdations
« on: July 28, 2014, 09:19:21 pm »
I use 40 all around has a little more give

12
Driveline / Re: centrifugal clutch recomdations
« on: July 28, 2014, 04:40:01 pm »
I like Norman star never had issue on single or twin I use the blue springs

13
Kohler Engines / Re: kohler vs intek
« on: July 25, 2014, 05:58:16 am »
Thiers a few now I think I less they sold

14
Briggs OHV & Vanguard / Re: EC Roller Rocker Installation: 33 vs. 31
« on: July 24, 2014, 07:50:35 pm »
Kohler .. Tecumsha ... Honda

15
Briggs OHV & Vanguard / Re: 31 ci info
« on: July 14, 2014, 10:34:12 pm »
U can just need them terned down so brass slides on

Pages: [1] 2 3 ... 92