Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - scootertrash

Pages: [1]
1
Drag Mowers / Re: My B&S Mini fuel altered dragster
« on: April 12, 2011, 10:33:59 pm »
I wanna hear it run. Those one into four headers must have a unique sound. Very impressive ride!

sounds pretty good, a lot of people comment on how it sounds, there is a crossover / balance tube between the two cylinders also, its painted black and behind the battery so its not noticeable.

2
Drag Mowers / Re: My B&S Mini fuel altered dragster
« on: April 12, 2011, 08:34:38 pm »
nice very nice well done got a top view off a latter

 


3
Drag Mowers / Re: My B&S Mini fuel altered dragster
« on: April 12, 2011, 07:39:48 pm »
thanks for the kind words, I built everything and then did all the powdercoating too.
My current project is a mini drag bike with the 18 kohler command, then on to the mini boat tailed speedster and mini "dragula" grandpa munsters draggin coffin

4
Drag Mowers / Re: My B&S Mini fuel altered dragster
« on: April 12, 2011, 06:24:24 pm »
what does it have for a trany
slipper clutch to jack shaft to limited slip diff.
geared at present it will max out in the 60 mph range, geared differently yanks the wheels and maxes out in the 45+ mph range.

5
Drag Mowers / Re: My B&S Mini fuel altered dragster
« on: April 12, 2011, 06:11:37 pm »
looks sweet is that a wheelbarrow for the body
yup, cut up a wheelbarrow

6
Drag Mowers / My B&S Mini fuel altered dragster
« on: April 12, 2011, 04:27:46 pm »
made everything from scratch, motor is 18hp briggs w/ shaved heads



 

7
Coffee Shop / Re: Drilling stock flywheel? Kohler ch18
« on: April 12, 2011, 04:06:24 pm »
oky doky then, thanks for the replies, I wont do it then.

8
Coffee Shop / Drilling stock flywheel? Kohler ch18
« on: April 12, 2011, 11:50:33 am »
I have the means to do the drilling, I could put it on an indexer and drill it evenly in hopes of keeping the balance correct. Am I thinking correctly or ?
This is a stock motor with a carb and exhaust upgrade.
Thanks

9
Coffee Shop / Re: CH18, 1.25" shaft....what fits it?
« on: April 12, 2011, 09:48:32 am »
okies, if thats what needs to be done, I'll machine it, was kinda hoping for not having to do that.

aaaaaand.....

Why was this moved to the coffee shop? a specific Kohler crank question would belong in the Kohler engine forum for best exposure and possible replies.....just askin, not trying to be a smarty :P

10
Coffee Shop / Re: CH18, 1.25" shaft....what fits it?
« on: April 12, 2011, 08:29:36 am »
I would like to put a torque drive hub on it,  I'm stuffing it into a small minibike and need something to get the driveline construction started. I searched google like mad looking for anything for the 1.25" shaft on the Kohler 18

11
Coffee Shop / CH18, 1.25" shaft....what fits it?
« on: April 11, 2011, 11:17:21 pm »
I'm having a HECK of a time locating anything that will slide on a 1.25" shaft ....
Kohler CH18S twin

thanks tons in advance.
PS, I'm new here, so I'll post up pictures of my B&S 18hp mini fuel altered later.

Pages: [1]