Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - dmswinney28

Pages: [1] 2
1
Briggs Flathead / Re: Opposed pistons
« on: April 23, 2016, 09:24:41 pm »
Will there not be enough material  after boring

2
Briggs Flathead / Opposed pistons
« on: April 23, 2016, 02:27:05 pm »
Is it possible to go bigger than 31ci pistons in a oppy

3
Briggs OHV & Vanguard / Re: 40ci single
« on: March 17, 2016, 08:28:41 am »
Thanks

4
Briggs OHV & Vanguard / 40ci single
« on: March 16, 2016, 01:03:35 pm »
I saw a post about 40ci big bore kits for a briggs single from ron does anyone know what rod and piston combo it is. Or is it something only from him.
Sorry the post said 4inch big bore kits not 40ci. Of course I don't know how many ci a 4inch bore would make it.

5
Briggs Flathead / Re: Oppy with dual carbs?
« on: March 08, 2016, 08:13:37 am »
Sorry it's sold already it looked exactely like one in pic above tho.

6
Briggs Flathead / Re: Oppy with dual carbs?
« on: March 07, 2016, 05:17:42 pm »
There was one for sale on ebay for 200 plus shipping search under racing lawnmower. It's only a block carbs and adapters tho.

7
Chassis / Heim joints
« on: February 22, 2016, 05:03:36 pm »
When ordering the 4 heim joints for my spindles do u need a left and right side heim joints or just all left or right I know ones for steering arm need to get both but wasn't sure on one's for spindles.

8
Chassis / Re: Size of front axle beam
« on: February 17, 2016, 12:05:32 pm »
I figured the 2x2 by quarter was overkill and heavy

9
Chassis / Size of front axle beam
« on: February 17, 2016, 08:14:20 am »
What size beam front axle does most people normally use I have a piece of 2x2 x1/4 inch tubing
 Is that too too heavy overkill. What is normally used that I see. Thanks

10
Driveline / Re: What type of trans
« on: February 10, 2016, 07:50:59 am »
Cool thanks for info

11
Driveline / Re: What type of trans
« on: February 10, 2016, 07:23:11 am »
Can u still order the gearset for the 017 kit iv seen post with part numbers u need for the conversion

12
Driveline / Re: What type of trans
« on: February 09, 2016, 09:30:31 pm »
Yeah i snapped the main shaft for the sprocket on my first  race and keys already don't look too great I'm building a new machine and have never ran 820 but I have one thanks for input

13
Driveline / What type of trans
« on: February 09, 2016, 12:19:48 pm »
Iv been running a 700 in cp is there and performance advantages over having a 820 with 017 gearset are they fairly the same or would there be a big torque advantage one over the other .

14
Kohler Engines / Kohler opposed twin
« on: February 07, 2016, 11:16:46 pm »
Are parts avaliable for these like the briggs opposed or do they have to be custom made iv searched and found nothing. It's a vertical BTW

15
Chassis / Re: Clutch
« on: November 27, 2015, 06:57:39 pm »
I change my setup and went to one size smaller belt and that worked. I'm guessing belt was just a tad too loose.

Pages: [1] 2
anything