Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - teddygraham

Pages: [1] 2
1
Briggs OHV & Vanguard / Re: I need 1 good 29 cubic inch vanny piston
« on: July 07, 2009, 10:14:48 pm »
what is this Indian engine you guys are talkng about

2
Briggs Flathead / Re: Show us your interest for a Billet Crank
« on: July 02, 2009, 05:22:52 pm »
any news

3
Briggs OHV & Vanguard / Re: Model 28 ohv fuel pump?
« on: July 01, 2009, 07:09:28 pm »
if you have a fuel tank below the carb will this help to bring the fuel up to it or will it have enough suction to bring it up to its level 

4
Briggs OHV & Vanguard / Model 28 ohv fuel pump?
« on: July 01, 2009, 06:18:59 pm »
what dose a fuel pump run off of and if the original engine did not come with one can a mod be done so one can be used and wondering would this help the engine at all would it give power or what thanks in advance

5
Driveline / Re: Identifying Lawn Mower Transmissions
« on: June 09, 2009, 09:24:44 pm »
ya as long as they dont let the engine to tranny belt run for a while it heats it up real bad

6
Driveline / Re: Identifying Lawn Mower Transmissions
« on: June 09, 2009, 06:22:21 pm »
Mine is on a mustang, is that an MTD brand?





Notice: The chain gear can be on either side of the tranny.



I had that tranny and the same tractor i blew it up it sucked that little guy had a good bit of hours on it its solid if it is not ran fast its good for tracotr pulling i herd

7
Briggs OHV & Vanguard / Re: Model 28 OHV briggs
« on: June 05, 2009, 09:10:52 pm »
that day was my first race i broke before i could really race but the only semi injured person that day was a guy that has not been on a fast mower for a while went to fast around the corner got up on two wheels slap back down and he started to turn again he flipped it and got the wind knocked out of him he was the only one on the track my buddys dad was letting ppl ride hes like thats the last time i let some one borrow the tractor  we only had a couple racers not to crowded on the track it could be improved i understand with the saftey, i want to get another tractor and go all out on it look at some classes to run on any suggestions, also back to engine mods please what should i shave the head down how many thousands

8
Briggs OHV & Vanguard / Re: Model 28 OHV briggs
« on: June 05, 2009, 07:42:45 pm »
i agree with the safe racing we are just making them fast for now with pulleys, and other minor mods, we were just in the patriot news about racing lawn mowers in pa, we're transitioning into official all rules followed racing but right now its about having fun not spending to much money on the mowers, were in the old days getting them fast, tinkering with the tractors and being safe we all wear helmets and such  i personally want to go faster and have rules followed but that takes plenty of $$ but there just some good competition races    without the politics excuse my french :D

9
Briggs OHV & Vanguard / Re: Model 28 OHV briggs
« on: June 04, 2009, 09:55:48 pm »
no the carb would not let enough fuel in so it has a hole drilled into the side of the brass so it works now and what are you talking about steering the ppl i race with are about being cheap no official racing yet but im sure we will get there

10
Briggs OHV & Vanguard / Re: Model 28 OHV briggs
« on: June 04, 2009, 09:34:09 pm »
i plan on putting on a fly wheel but the only real mods are a bypassed external governor and modified carb to give more gas in higher revs

11
Briggs OHV & Vanguard / Re: Model 28 OHV briggs
« on: June 04, 2009, 03:09:50 pm »
how many thousands should i shave of of it
 :doh:

12
Briggs Flathead / Re: Show us your interest for a Billet Crank
« on: June 04, 2009, 10:59:55 am »
well thats good, i guess it would be smart to make the two sizes some ppl might get upset if some ppl can use in there class and others can not

13
Briggs OHV & Vanguard / Re: Model 28 OHV briggs
« on: June 04, 2009, 10:52:14 am »
i have a question i was pitched an idea that if you were to shave the head down on the model 28 you gain compression dose it do anything for power or dose it just casuse problems and its a wast of time

14
Briggs Flathead / Re: Show us your interest for a Billet Crank
« on: June 04, 2009, 10:45:24 am »
Where is the crank in its current state are you still desgineing it or did you get to the testing stage  :stickdance:

15
Briggs OHV & Vanguard / Re: Model 28 OHV briggs
« on: June 02, 2009, 09:48:07 pm »
i will be looking out for those the anticipation is unbearable :woo:  but i guess i have to wait

Pages: [1] 2
anything