Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Topics - crazycraftsman

Pages: [1] 2 3 ... 9
1
Briggs OHV & Vanguard / Bore a 28 cube to 31 cube .020 over
« on: June 07, 2017, 12:38:36 am »
Has anyone bored a 28 to 31 cubes with success. Can't find a 31 non avs block local and we need it together in a week.

2
Briggs OHV & Vanguard / 05 early or 05 late 38 vanguard blocks
« on: October 31, 2016, 03:30:53 pm »
Is one better than the other, is there any differences? Thanks for any info

3
Tires / 6"/6" beadlock rims
« on: October 29, 2016, 01:48:49 pm »
Is there anymore company's out there making these besides Qrc? Looks like Douglas only makes 8" and up. Thanks from any info.

4
Briggs OHV & Vanguard / 38 vangaurd stock bore size?
« on: September 06, 2016, 01:26:32 pm »
Got some used blocks and trying to find out if they have been already bored over . What's the safe over size to go? Any help would be appreciated.

5
Briggs OHV & Vanguard / Compression change from 208 psi to 250 psi
« on: August 27, 2016, 08:16:02 pm »
This is on a 35 vanny twin . Was running 92 non ethonal , should I change to vp 110 race gas? Will help it run cooler? More compression more heat right? Thanks for any help

6
Coffee Shop / Where's a good well known place to get heads built?
« on: July 23, 2016, 06:03:37 pm »
Big valves, titanium,seats put in and guides. Thanks for any info.
Looking for a reliable , honest and are experienced.

7
Coffee Shop / OEM denso starter Vs aftermarket
« on: February 23, 2016, 09:04:28 pm »
Is there a way to tell the difference ? Thanks

8
Chassis / Hood bunges ( hold downs)
« on: January 06, 2016, 09:47:10 pm »
Does anyone know what there called? I've seen a lot of people using small (3-4") rubber tie downs. One end bolt to hood other end has a hook. Then you just pull down and hook it to a bolt or hole below hood. Anyone know were to buy? Thanks

9
Tires / Tube size for Ec 8x8 rims
« on: January 01, 2016, 12:36:43 pm »
16/7.5/8 turf savers . Is there a tube size that works better , that does not bow center of tires out?
I tryed 16/7.5/8 tubes and they bow these 2 ply tires pretty good at 10psi. Better off not running tubes with these tires? Or a bigger tube? Thanks for any info
I never ran tubes in my 13" tires but a little worried about the 16".

10
Tires / Carsile turf saver 16/7.5/8
« on: December 09, 2015, 11:50:11 pm »
I've looked on there web site and only offer this tire in 2ply. Do these tires side walls hold up well in racing on tacky clay tracks?

11
Briggs OHV & Vanguard / 31-33 Avs factory pistons
« on: November 21, 2015, 07:01:56 pm »
Are the pin heights the same on 31  and 33 Avs pistons?

12
Driveline / 13' tire/ 41' roll vs 16' tire/50' roll
« on: November 12, 2015, 03:36:25 pm »
Im changing my tires from 13/6' rim - 16'/8'rim to make the uslmra rule in the classes i'll be running. Is there a big increase in speed with the 9' longer roll out? Thanks

13
USLMRA Races / Engine orientation rule
« on: October 10, 2015, 01:08:55 pm »
I'm building two mtd class mowers. Cp/Bp .One chassi has engine hole in center of frame and the other offset to the left 2" off center. Can I center the motor in the middle of the chassi? I will not be moving forwards or backwards just centering. Thanks for clarification in advance.

14
Coffee Shop / HD denso starters
« on: October 04, 2015, 03:49:15 pm »
Do the denso starters on kolar v-twins and singles fit on briggs twins and singles?

15
Chassis / Widening fenders
« on: September 14, 2015, 12:46:45 am »
I've read the uslmra rule book several times and was wondering can I widen the fenders over the tires? So the fenders stick out 1-1.5" past tires.

Pages: [1] 2 3 ... 9