Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - BlueBayou

Pages: [1] 2 3 ... 7
1
Racing Mower Builds / Re: 2012 Super Modified Twin
« on: December 28, 2011, 09:24:17 pm »
so on all your build do you always offset both axle's to the right? also do you set both your plates that hold your heims on the front axle at 10-12 degree's or just the right side?

2
Coffee Shop / Re: dodge fans
« on: December 06, 2011, 09:26:13 pm »
Have owned 4
1998 3500 flatbed 24v cummins 5spd - good truck
2001 2500 24v cummins auto (junk)- pushing 450-475 horse didnt help the auto but it was fast when i held together
1994 2500 12 5spd 336,000 run like a scalded dog used no oil either.
2002 mini van -wifes rig. Junk also.

3
Tecumseh Engines / Re: 17 HP counterbalance
« on: December 04, 2011, 09:27:09 pm »
I have run and heard to just take them out. Mine have held up well without them. No noticable gains in hp but its less weight to turn inside your motor

4
Chassis / Centering rear axle and stagger
« on: December 04, 2011, 09:07:27 pm »
When building a kart style rear end, 1 inch axle chain drive etc.  Do you make your axle center with your chassis and do you make it with a stagger or put it in straight in comparison with your front end ?

5
Chassis / Re: Easy Radius Rods!
« on: December 04, 2011, 08:44:34 pm »
Thanks for the quick reply. I will give them a try.

6
Chassis / Re: Heim joints..
« on: December 04, 2011, 08:36:25 pm »
Haha just found that company after my post. DUH me but thanks for your reply probly will use 5/8's since i have all the stuff for it besides the joints. Anyone know how they do on shipping?

7
Chassis / Re: Easy Radius Rods!
« on: December 04, 2011, 08:34:55 pm »
With that Mcmaster company how fair is their shipping? i entered all the parts i wanted and it would give me a shipping price. Maybe i computer dumb i dunno

8
Chassis / Heim joints..
« on: December 04, 2011, 08:14:37 pm »
Where do you guys get these for a decent price? i can't find them anywhere around my home town. Also what is a good size for the front spindle's ? Was thinking 5/8's would be sufficent enough. Thanks for the input.

9
Non-Affiliated Races / Re: 2012 Indoor Winter Nationals - Springfield, MO
« on: October 12, 2011, 09:05:19 pm »
What did it cost last year? Any ideas of how much it will be this year?

10
Tecumseh Engines / Re: 17Hp Tec
« on: October 05, 2011, 10:01:49 pm »
Yea that's what i figured calling them if i was going to order parts. I was trying to down them i really like their stuff and i'm sure its hard to keep on top of all the different models that we use racing. Will definatly be calling them this winter for some parts on a new build.

11
Tecumseh Engines / Re: 17Hp Tec
« on: October 04, 2011, 05:48:22 pm »
The ec site doesnt specify which motor they are for? Maybe my bad vision like the flywheel and cam? it doesnt say ohv 17 or if their for a 10 hp?

12
Tecumseh Engines / Re: Carb and fuel pump
« on: September 20, 2011, 10:23:06 pm »
getting the pulse from the a elbow i brass'ed in the valve cover. Tryed the intake now seems to work ok just have'nt had it out on the track yet.

13
Tecumseh Engines / Re: Carb and fuel pump
« on: September 19, 2011, 10:52:24 pm »
how in the heck do i externaly vent it? I'll search on here but it's a briggs carb. Free motor didnt have no carb on it so i had to make do with what i had. Ran great all year then starting doing this the past 3 races. there was oil in the line that goes to the fuel pump, could that be a problem? thanks George.

14
Coffee Shop / Re: HR tillson help
« on: September 19, 2011, 10:47:52 pm »
If you dont mine asking where did you get your carb or where can they be "found"? thanks

15
Tecumseh Engines / Carb and fuel pump
« on: September 13, 2011, 09:51:37 pm »
Whats the best fuel pump to use or what is everyone using, on a ohv17, i fi run no pump it spits and sputters in the rough or coming out of the corner's also what's the best source to get your air from to run the pump? thanks

Pages: [1] 2 3 ... 7